Vores kunder ligger øverst på Google

Google Ads Specialister fra Vestjylland

Vi er 100% dedikerede til Google Annoncering – Vi har mange års erfaring med Google Ads og den bruger vi på at opsætte, optimere & vedligeholde vores fantastiske kunders konti.

100% Specialiseret i Google Ads
Vi har mange års erfaring fra +300 konti
Ingen lange bindinger & evighedskontrakter
Jævnlig opfølgning med hver enkelt kunde
Vi tager din virksomhed seriøst
KONTAKT OS
LÆS UDTALELSER & SUCCESHISTORIER

20 results (0,14665 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

C-Tec CA732 CA Zone Monitor Module

C-Tec CA732 CA Zone Monitor Module

C-Tec CA732 CA Zone Monitor Module The C-Tec CA732 is a CA Zone monitor module using the C-TecCAST analogue addressable protocol.CAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key FeaturesLPCB certified to EN54-17 18 and Kiwa Teleficationcertified to EN54-13A single-zone addressable Zone Monitor capable of supportingup to 20 conventional fire detectors and 10 MCPsMountable on a standard UK 25mm double gang back boxOnboard short-circuit loop isolator4mA typical alarm current 1.1mA typical quiescent current 22-40V DCIndicators for Loop polling input faults and relay statusAlternatively can be used as general purpose input monitorMountable on a C-TEC NCP-26 surface box or a standard UK25mm double gang back box not supplied

GBP 44.86
1

C-Tec CFP763 Relay Output Card as per CFP762 8 outputs per zone relays

C-Tec CFP763 Relay Output Card as per CFP762 8 outputs per zone relays

C-Tec CFP Relay Output Card as per CFP762 8 outputs per zone relays CFP763An optional system expansion device for use withCFP Standard 2-8 Zone Fire PanelsorCFP AlarmSense 2-8 Zone Fire Panels.Key FeaturesProvides four panel-controlled volt free relay outputs reset fault aux. fire and remote and eight output per zone relays.PCB mounts inside the CFP fire panel.Reset relay is active during the panels reset cycle.Fault relay is active in any fault condition. This relay is failsafe and normally energised - if power is removed from the panel the relay will changeover to produce a fault signal.Aux. fire relay is active in an alarm condition provided all relevant delays have expired.Remote relay is active during any Alarm Condition provided all relevant delays have expired.Output per zone relays will changeover when the corresponding zone is in alarm subject to certain conditions - for full details refer to the instructions downloadable below.Outputs are NOT designed to switch mains voltages.

GBP 67.02
1

C-Tec NC944 Four Zone Call Controller with Mute Reset Button

C-Tec NC944 Four Zone Call Controller with Mute Reset Button

C-Tec NC944 Four Zone Call Controller with Mute Reset ButtonThe NC944 Four Zone Call Controller is compatible with all 800 Series call points ceiling pulls infrared ceiling receivers monitoring points overdoor lights and remote sounders.Depending on how the Controller is configured and the devices connected to it Standard and Emergency calls can be indicated via its buzzer and zonal LEDs. Two buttons are also provided to allow the user to Reset or Mute standard calls as detailed below.Standard Calls when triggered by a calling device the Controllers internal buzzer sounds continuously and the relevant zone indicators illuminate steady.Pressing the Controllers Reset Button if enabled cancels all standard calls.Pressing the Controllers Mute Button if enabled silences the Controllers internal buzzer. However if a new call standard or emergency is triggered anywhere on the system the buzzer will resound.Emergency Calls when triggered by a calling device the Controllers internal buzzer pulses and the relevant zone indicators flash. This level of call takes priority over standard calls and cannot be muted accepted or reset at the Controller. An emergency call can only be reset at the device from which it was triggered or via a reset point wired on the same zone.Key FeaturesAn attractively-designed four zone call controller cw mute and reset buttonsFully compatible with C-TECs entire range of 800 Series Call System componentsCapable of indicating standard constant tone and emergency intermittent tone callsRequires a separate NC930 12V 250mA PSUIncludes four zonal alarm LEDs RESET and MUTE buttonsTwo open collector outputs Emergency and Aux OutUp to two NC944s can be connected to one NC930 PSU to create a mini-call system of up to 8 zonesMounts on a standard 25mm UK double gang back box

GBP 75.00
1

C-Tec XFP761 XFP Network Card For 16 Zone Panels

C-Tec XFP761 XFP Network Card For 16 Zone Panels

C-Tec XFP761 XFP Network Card For 16 Zone PanelsThe XFP network card allows for the connection of up to eight mainpanels any mix over a two-wire RS485 network spanning up to 1KM. Eachnetworked XFP panel can be programmed to receive fire alerts faults andcontrol commands such as silencing alarm sounders and resetting controlpanels from other connected panels.Key FeaturesCan be used to connect up to 8 XFP repeaters any mix toone XFP main panelUp to 500m of cable may be fitted to an XFP two-wirerepeater networkEach XFP repeater offers all the functions and controls ofan XFP main panelThe XFP main panel must have a network communication cardfittedIt is not possible to mix XFP main panels and XFP repeaterson the same networkOne XFP761 required per networked Main XFP Single Loop 16Zone fire panel note that XFP510-16 and XFP510-32 repeaters include a networkdriver card as standardThe XFP761 is NOT compatible with XFP 12 Loop32 Zone fire panels which require an AFP711 card for networking

GBP 74.52
1

C-Tec FF502P Four Zone Monitored Sounder Extended Double Gang

C-Tec FF502P Four Zone Monitored Sounder Extended Double Gang

C-Tec FF502P Four Zone Monitored Sounder Extended Double GangThe FF502P provides four extra sounder circuits with open and short circuit fault monitoring. It is compatible with most fire alarm control panels and is supplied mounted on a double gang plate which fits standard UK 25mm deep back boxes.Key FeaturesBasic connection requires four wires 24 VDC 0V Sounder Ve Sounder VeSounder -Ve Sounder Ve can be connected at the host panel or any convenient point on a sounder circuit DO NOT SPUR. 24 VDC and 0V can be derived from the host panel or alternatively from an external PSUIf connecting the FF502P to a C-TEC fire panel only three input control wires are required Sounder -Ve is not required as our conventional panels have a common 0V railFits on standard UK 25mm flush or surface mount back boxes

GBP 72.70
1

C-Tec CFP Relay Output Card Reset Fault Aux amp Remote Relay Outputs CFP762

C-Tec CFP Relay Output Card Reset Fault Aux amp Remote Relay Outputs CFP762

C-Tec CFP Relay Output Card Reset Fault Aux Remote Relay Outputs CFP762An optional system expansion device for use withCFP Standard 2-8 Zone Fire PanelsorCFP AlarmSense 2-8 Zone Fire Panels.Key FeaturesProvides four panel-controlled volt free relay outputs reset fault aux. fire and remote.PCB mounts inside the CFP fire panel.Reset relay is active during the panels reset cycle.Fault relay is active in any fault condition. This relay is failsafe and normally energised - if power is removed from the panel the relay will changeover to produce a fault signal.Aux. fire relay is active in an alarm condition provided all relevant delays have expired.Remote relay is active during any Alarm Condition provided all relevant delays have expired.Outputs are NOT designed to switch mains voltages.

GBP 46.63
1

C-Tec CFP EN54-13 Interface Board BF354

C-Tec CFP EN54-13 Interface Board BF354

C-Tec CFP EN54-13 Interface Board BF354BSI certified to EN54-13 Fire detection and fire alarm systems compatibility assessment of system components. Fits inside a CFP standard 2-8 zone fire panel to provide two EN54-13 monitored sounder circuits.When used in conjunction with the CFP Standard 2-8 Zone Fire Panels ActiV fire detectors and a wide range of specified sounders VADs and call points installers can rest-assured the system they are installing is fully compliant with the system compatibility requirements of EN54-13 and is certified as such by the BSI.Key FeaturesMonitorsits onboard sounder circuits for partial and full open or short circuit faults when used in conjunction with a BF355 fault monitoring module one BF355 required per sounder circuitIdeal for use in territories where EN54-13 is mandated such as Germany the Netherlands and Belgium

GBP 78.54
1

C-Tec NC887D Conventional Switchable Sounder

C-Tec NC887D Conventional Switchable Sounder

C-Tec NC887D Conventional Switchable SounderThe NC887D can be connected to any multi-zone 800 Series Call Controller or MasterIndicator Panel to increase call indication levels.Key FeaturesIndicates Standard calls via a constant tone and Emergency calls via a pulsing toneCan beswitched off when not required e.g. during night shifts to reduce call indication levelsCan control up to twoNC888D remote soundersWhen switched OFF a red reassurance LED will illuminateas a warning

GBP 53.72
1

C-Tec CA730 CA Input Output Module

C-Tec CA730 CA Input Output Module

C-Tec CA730 CA Input Output ModuleThe C-Tec CA730 is an addressable input output interfacemodule using the C-Tec CAST analogue addressable protocol.CAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key FeaturesLPCB certified to EN54-17 18 and Kiwa Teleficationcertified to EN54-13Incorporates the functions of a switch monitor zone monitorand output unitUp to 20 conventional detectors 10 MCPsAny normally open switch with an EOL resistor fittedA simple normally open or closed switch non-faultmonitoredOnboard short-circuit loop isolator5.5mA typical alarm current 1.3mA typical quiescentcurrent 22-40V DCIndicators for Loop polling input faults and relay statusCan switch 1A30V DC or 0.3A125V ACIncludes volt free changeover contacts that can be used totrigger rollershutter doors gas shut-off valves smoke vents etcMountable on a C-TEC NCP-26 surface box or a standard UK25mm double gang back box not supplied

GBP 51.37
1

C-Tec CA731 CA Mains Switching Input Output Module

C-Tec CA731 CA Mains Switching Input Output Module

C-Tec CA731 CA Mains Switching Input Output Module The C-Tec CA731 is a mains switching input output interfacemodule using the C-Tec CAST analogue addressable protocol.CAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key FeaturesLPCB certified to EN54-17 18 and Kiwa Teleficationcertified to EN54-13A mains-switching version of our CA730 input output moduleCapable of switching 5A 230 V AC or 5A 30V DCIncorporates the functions of a switch monitor zone monitorand output unitUp to 20 conventional detectors and 10 MCPsAny normally open switch with an EOL resistor fittedA simple normally open or closed switch non-faultmonitoredOnboard short-circuit loop isolator6mA typical alarm current 1.7mA typical quiescent current 22-40V DCIndicators for Loop polling input faults and relay statusIncludes volt free changeover contacts that can be used totrigger rollershutter doors gas shut-off valves smoke vents etcMountable on a C-TEC NCP-26 surface box or a standard UK25mm double gang back box not supplied

GBP 60.32
1

C-Tec BF433CF5 FUL ROLP LX 24V W Class Sounder VAD - Red Body - Red Flash

C-Tec BF433CF5 FUL ROLP LX 24V W Class Sounder VAD - Red Body - Red Flash

C-Tec BF433CF5 FUL ROLP LX 24V W Class Sounder VAD - Red Body - Red FlashThe RoLP LX sounder is ideal for dual use applications where a visual alarm device VAD is required to support an audible alarm.Recommended for wall use and requiring just one installation point the RoLP LX Wall is available to use with any standard RoLP sounder such as the high output RoLP Maxi sounder.As well as European EN54-23 certification the RoLP LX Wall VAD has extensive country-specific AFNOR CNBoP and AS certifications and models specific to NF and VDS approvals.The patented long life LED lens optics used in the LX have been developed specifically for the VAD EN54-23 standard.It uses modern thick-mould injection moulding techniques and innovative cylindrical output to achieve the correct level of illumination while keeping power consumption as low as possible.Key FeaturesCertified to EN54 Parts 3 and 23 AFNOR and 13 BSIProvides W-2.4-7.5 coverage switchable to W-2.4-2.5 if required102dBA sound output22-37mA alarm current depending on settingAttractive slim designUltra-bright red LEDIdeal for use in bedrooms bathrooms and toilets

GBP 78.86
1

C-Tec XFP508H Hush Button Hochiki ESP Protocol

C-Tec XFP508H Hush Button Hochiki ESP Protocol

C-Tec XFP508H Hush Button Hochiki ESP ProtocolThe XFP508H Hush Button has been specifically designed to reduce the incidence of false alarms in houses of multiple occupation by providing reliable fully monitored fire detection alarm and silencing facilities inside each individual flat or apartment.It can be looked upon as a miniature loop-powered single zone fire alarm controller that sits and is addressed on an Hochiki ESP analogue loop with the ability to communicate its status back to the host panel. On a typical system one Hush Button is fitted in each dwelling complete with conventional detectors and conventional sounders to provide occupants with a simple means of invoking two types of hushed period.By providing occupants with this level of control over their fire alarm systems it helps reduce false alarms and prevent unnecessary building evacuations system vandalism and the likelihood of a true alarm signal being ignored.Key FeaturesUpgrades the level of protection offered in a flat or apartment from the Grade D minimum mainsbattery smoke alarms to Grade A or BProvides each individual dwelling with a 2 minute silence facility and 15 minute isolate facility to BS 5839 pt 6 clause 12.2Can be operated by building occupants whilst standing at floor levelIncludes a built-in loop isolator conventional sounder circuit conventional detector circuit and three status LEDsFully monitored for open and short circuit faults logging facilities at the host panel give full traceability of any problemsFailsafe operation - a general fire condition at the host panel will override any silencedisolated state at the hush button and immediately turn on its local soundersOperation of a manual call point fitted with a resistor of less than 400 ohm will immediately trigger the host panel a 330 Ohm resistor is suppliedCommon OV line allows sounders and detectors to be wired in three core cable

GBP 74.52
1

C-Tec XFP508X Hush Button Apollo XP95 Discovery Protocol

C-Tec XFP508X Hush Button Apollo XP95 Discovery Protocol

C-Tec XFP508X Hush Button Apollo XP95 Discovery ProtocolThe XFP508X Hush Button has been specifically designed to reduce the incidence of false alarms in houses of multiple occupation by providing reliable fully monitored fire detection alarm and silencing facilities inside each individual flat or apartment.It can be looked upon as a miniature loop-powered single zone fire alarm controller that sits and is addressed on an XP95 Discovery or Xplorer analogue loop with the ability to communicate its status back to the host panel. Typically one Hush Button is fitted in each dwelling complete with conventional detectors and conventional sounders to provide occupants with a simple means of invoking two types of hushed period.By providing occupants with this level of control over their fire alarm systems it helps reduce false alarms and prevent unnecessary building evacuations system vandalism and the likelihood of a true alarm signal being ignored.Key FeaturesUpgrades the level of protection offered in a flat or apartment from the Grade D minimum mainsbattery smoke alarms to Grade A or BProvides each individual dwelling with a 2-minute silence facility and 15 minute isolate facility to BS 5839 pt 6 clause 12.2Can be operated by building occupants whilst standing at floor levelIncludes a built-in loop isolator conventional sounder circuit conventional detector circuit and three status LEDsFully monitored for open and short circuit faults logging facilities at the host panel give full traceability of any problemsFailsafe operation - a general fire condition at the host panel will override any silencedisolated state at the hush button and immediately turn on its local soundersOperation of a manual call point fitted with a resistor of less than 400 ohm will immediately trigger the host panel a 330 Ohm resistor is suppliedCommon OV line allows sounders and detectors to be wired in three core cable

GBP 74.52
1