led bloklys from GBP 6 | See the cheapest prices and offers on css.nordicadpartner.dk

Global Fire Equipment GFE-C-REM-INDBLK GFE Standard Remote Indicator with Flashing LED - Black

Global Fire Equipment GFE-C-REM-INDBLK GFE Standard Remote Indicator with Flashing LED - BlackThis remote indicator can be used with any fire alarm detector be it of the conventional types to indicate remotely the activation of the relevant detection device.Its main characteristics are the high visibility due to the flashing of two high efficiency LEDs and the wide operating voltage range 3.3V to 10V DC with a maximum 7mA current consumption. The connections of this device are non-polarised.Key FeaturesFlashing LEDCan be used with any fire alarm detectorColour Black

GBP 8.82

1

Global Fire Valkyrie CB Conventional Red Beacon

Global Fire Valkyrie CB Conventional Red BeaconThe VALKYRIE CB is a Conventional Beacon produced using the latest high intensity LED technology and use extremely low levels of current consumption providing a highly visible flash. It can be supplied in either white or red colour.Key FeaturesLow current consumptionHigh intensity LED technology

GBP 25.07

1

Global Fire Equipment VALKYRIE-CBWHT Valkyrie Conventional Wall Mount Beacon White

Global Fire Equipment VALKYRIE-CBWHT Valkyrie Conventional Wall Mount Beacon WhiteThe VALKYRIE CB is a Conventional Beacon produced using the latest high intensity LED technology and use extremely low levels of current consumption providing a highly visible flash.Compatible with most conventional panels.Key FeaturesHigh intensity LED technologyLow levels of current consumptionColour White

GBP 25.07

1

Global Fire Valkyrie CB IP65 Conventional Red Beacon

Global Fire Valkyrie CB IP65 Conventional Red BeaconThe VALKYRIE CB IP65 is a Wall Mounted Conventional Beacon produced using the latest high intensity LED technology and use extremely low levels of current consumption providing a highly visible flash. It is specifically designed to be used outdoors.Key FeaturesIP65 ratedHigh intensity LED technologyLow current consumption

GBP 34.46

1

Global Fire Equipment GFE-MULTI Multi IO Module - 4 x ZMU 3 x LSC 2 x Aux. Relays

Global Fire Equipment GFE-MULTI Multi IO Module - 4 x ZMU 3 x LSC 2 x Aux. RelaysThe MULTI-IO is a fully monitored addressable module which can be used with Global Fire Addressable fire alarm control panels.The module provides four Zone Monitor Units three Sounder Units and two system auxiliary Relays.The module requires an external 24V DC power supply. A Dedicated green LED indicates if a power supply is present.The module has selectable Active or Resistive End of Line Monitoring for the Zone Monitor Units. The status of each zone is indicated by two LEDs. A Red LED signals Fire Yellow indicates Fault on that zone.Key FeaturesLoop monitored for Open Circuits Short CircuitsMaximum 32 devices per Zone1A Maximum combined current drive for S1 S2 and S3Powered from 24V external supplyFour consecutive addresses selection Zone Monitor UnitsSeven consecutive addresses selection Four Zone Monitor Units Three Sounder UnitsActive or Resistive end online

GBP 63.88

1

Global Fire Equipment GFE-C-REM-IND GFE Standard Remote Indicator with Flashing LED

Global Fire Equipment GFE-C-REM-IND GFE Standard Remote Indicator with Flashing LEDThis remote indicator can be used with any fire alarm detector be it of the conventional types to indicate remotely the activation of the relevant detection device.Its main characteristics are the high visibility due to the flashing of two high efficiency LEDs and the wide operating voltage range 3.3V to 10V DC with a maximum 7mA current consumption. The connections of this device are non-polarised.Key FeaturesFlashing LEDCan be used with any fire alarm detector

GBP 5.87

1

Global Fire Equipment GFE-ZMU-1 Addressable 1 Zone Monitoring Module

Global Fire Equipment GFE-ZMU-1 Addressable 1 Zone Monitoring ModuleThe QUAD-ZMU is a fully monitored addressable module which is used to connect up to four individually addressed zones of current-limited conventional detection devices to the Global Fire Addressable control panel via the detection loop.The module requires an external 24V DC power supply and a Green LED indicates supply presence. Active End of Line Monitoring. Compliance with Standard BS5839 Detector Removal when Schottky diodes are added to detector bases.The detection Zones and their supply voltage are optically isolated from the addressable detection loop which allows the use of a local power supply. If that supply fails a fault condition is reported at the control panel.The status of each zone is indicated by two LEDs. A Red LED signals Fire Yellow indicates Fault on that zone. The normal state is indicated by neither LEDs being illuminated.Each Zone can be programmed to reply as a Zone Monitor Flame Detector Beam Detector Aspirating Module or Linear Heat Device for better discrimination of Alarm status source.

GBP 60.26

1

Global Fire GFE-MCPE-AI Addressable Call Point with Isolator

Global Fire GFE-MCPE-AI Addressable Call Point with IsolatorThe GFE-MCPE-A is an Analogue Addressable Manual Call Point designed and manufactured to comply with EN54-11 compatible with all GFE Addressable Control panels. With its enhanced communications mechanism the typical response time when in alarm is approximately one second depending on the number of call points connected to the device loop. There is also a version incorporating a Loop Isolator.A bi-colour LED flashes Green when the unit is interrogated by the control panel and is illuminated Red when in Alarm. The command to illuminate the Red LED is emitted by the control panel in response to activation of the individual call point thus confirming that the Alarm signal has been received at the control panel. The individual address up to 125 of each call point is set via an eight way DIL switch.The unit is supplied complete with a hinged flap which protects the trigger element from accidental activation and reduces malicious activations as two actions are required in order to activate the device. This unit can be both surface and flush mounted and it can be easily reset using the supplied key after activation.

GBP 36.32

1

Global Fire GFE-MCPE-C Conventional Call Point

Global Fire GFE-MCPE-C Conventional Call PointThe GFE-MCPE-C is a Conventional Manual Call Point designed and manufactured to comply with EN54-11 compatible with all GFE Conventional Control panels. A bi-colour LED flashes Green when the unit is connected to a control panel and is illuminated Red when in Alarm.The unit is supplied complete with a hinged flap which protects the trigger element from accidental activation and reduces malicious activations as two actions are required in order to activate the device. This unit can be both surface and flush mounted and it can be easily reset using the supplied key after activation.

GBP 11.88

1

Global Fire Equipment VALKYRIE-CSBWHT Valkyrie Conventional Wall Mount Sounder Beacon White

Global Fire Equipment VALKYRIE-CSBWHT Valkyrie Conventional Wall Mount Sounder Beacon WhiteThe VALKYRIE CSB is a Conventional Sounder Beacon produced using the latest high intensity LED technology and use extremely low levels of current consumption providing a highly visible flash.Four different tones are available and selected using DIL switches 1 and 2.Both continuous and pulsing outputs are provided via separate negative supply connections allowing for the presence of differentiated evacuation and alert sounds.Key FeaturesSupply Voltage 20 V to 30 V DCDimensions 110 D x 85 H mm including baseIP Rating IP21C Type A Indoor useColour WhitePlease note The image is for illustrative purposes only. This product will come in white.

GBP 40.74

1

Global Fire Valkyrie AB Addressable Red Beacon

Global Fire Valkyrie AB Addressable Red BeaconThe VALKYRIE AB is a Wall Mounted Addressable Beacon with low power consumption. Up to 32 individually addressed beacons can be installed per loop occupying address 94 to 125. The address is set using switches 1 to 5 of the 8-way DIL switch.When individual address reporting is not required VALKYRIE AB can be configured as a Shadow Beacon. In this case sounders do not occupy an address in the loop thus freeing up addresses for more detection devices. Shadow beacons do not report back to the control panel so their presence on the loop is not monitored.Shadow beacons draw current from the loop 3 mA in alarm and must be included in loop load calculations. These units are produced using the latest high intensity LED technology and use extremely low levels of current consumption providing a highly visible flash.

GBP 37.91

1

Global Fire Valkyrie ABI IP65 Addressable Red Beacon with Isolator

Global Fire Valkyrie ABI IP65 Addressable Red Beacon with IsolatorThe VALKYRIE ABI IP65 is a Wall Mounted Addressable Beacon with Isolator and low power consumption. It is specifically designed to be used outdoors. Up to 32 individually addressed beacons can be installed per loop occupying address 94 to 125. The address is set using switches 1 to 5 of the 8 way DIL switch.When individual address reporting is not required VALKYRIE ABI IP65 can be configured as a Shadow Beacon. In this case sounders do not occupy an address in the loop thus freeing up addresses for more detection devices. Shadow beacons do not report back to the control panel so their presence on the loop is not monitored.Shadow beacons draw current from the loop 3 mA in alarm and must be included in loop load calculations. These units are produced using the latest high intensity LED technology and use extremely low levels of current consumption providing a highly visible flash.

GBP 65.70

1

Global Fire GFE-MCPE-C-IP67 Conventional Weatherproof Call Point

Global Fire GFE-MCPE-C-IP67 Conventional Weatherproof Call PointThe GFE-MCPE-C-IP67 is a Conventional Manual Call Point designed and manufactured to comply with EN54-11 compatible with all GFE Conventional Control panels specially recommended for outdoor use. The unit is supplied complete with a hinged flap which protects the trigger element from accidental activation and reduces malicious activations as 2 actions are required in order to activate the device.A bi-colour LED flashes Green when the unit is connected to a control panel and is illuminated Red when in Alarm. The GFE-MCPE-C-IP67 has been designed to deal with todays difficult and harsh environments. It is a unique fire alarm manual call point that mimics the feel of breaking glass whilst offering the user the benefits and safety advantages of a glass-free resettable operating element. Once activated a warning flag drops in to view easily identifying the call point that has been operated. A key can then reset the unit.The GFE-MCPE-C-IP67 provides an ideal solution for most conventional fire alarm systems. Ideal for all outside applications such as oil rigs ships factories as well as wash down areas that are sensitive to broken glass.

GBP 96.42

1

Global Fire GFE-MCPE-AI-IP67 Addressable Weatherproof Call Point

Global Fire GFE-MCPE-AI-IP67 Addressable Weatherproof Call PointThe GFE-MCPE-AI-IP67 is an Analogue Addressable Manual Call Point designed and manufactured to comply with EN54-11 compatible with all GFE Addressable Control panels specially recommended for outdoor use. With its enhanced communications mechanism the typical response time when in alarm is approximately one second depending on the number of call points connected to the device loop. The individual address up to 125 of each call point is set via an eight-way DIL switch. Each unit is supplied as standard with a loop short circuit isolator. A bi-colour LED flashes Green when the unit is interrogated by the control panel and is illuminated Red when in alarm.The GFE-MCPE-AI-IP67 has been designed to deal with todays difficult and harsh environments. It is a unique fire alarm manual call point that mimics the feel of breaking glass whilst offering the user the benefits and safety advantages of a glass-free resettable operating element.Once activated a warning flag drops in to view easily identifying the call point that has been operated. A key can then reset the unit. The GFE-MCPE-AI-IP67 provides an ideal solution for GFEs addressable fire alarm systems. Ideal for all outdoor applications such as oil rigs ships factories as well as wash down areas that are sensitive to broken glass.

GBP 143.18

1

Global Fire Equipment GFE-IO-3 Addressable 3-Channel IO Module CW Isolator

Global Fire Equipment GFE-IO-3 Addressable 3-Channel IO Module CW IsolatorThe 3 IO PLUS Modules are fully monitored loop powered devices which permit the interfacing of third-party equipment with the FireAlarm Control panel using normally open dry contact connections. Each module can be fitted with a maximum of 3 inputs and 3 outputs. The connection to each input is monitored for fault open or short circuit and alarm conditions.The interface is used to monitor the contacts of an external system which must be interfaced to the Fire Alarm System for example a Flow Switch in a sprinkler system to indicate if the sprinklers have been activated or extinguishant level monitoring in Gas Extinguishing Systems etc.Module is provided with a loop short-circuit isolator and with up to 3 voltage free single pole change over relay outputs. The output relays are always powered directly from the detection loop. It is not required to use an external 24V DC power supply. Relay operation is confirmed by an onboard Red LED. A 8 way D.I.L. switch is provided to configure the modules address. This value can be set in the range 1 to 125. The following programmable functions are available Input Activation Mode Delayed Input Alarm Activation Output Delayed Activation.Key FeaturesFast Activation ResponseLoop PoweredStatus LEDs for each IO and OPLow Power ConsumptionModule features an integral short-circuit loop isolator

GBP 82.61

1

Global Fire Equipment GFE-IO-2 Addressable 2-Channel IO Module CW Isolator

Global Fire Equipment GFE-IO-2 Addressable 2-Channel IO Module CW IsolatorThe 3 IO PLUS Modules are fully monitored loop powered devices which permit the interfacing of third-party equipment with the FireAlarm Control panel using normally open dry contact connections. Each module can be fitted with a maximum of 3 inputs and 3 outputs. The connection to each input is monitored for fault open or short circuit and alarm conditions.The interface is used to monitor the contacts of an external system which must be interfaced to the Fire Alarm System for example a Flow Switch in a sprinkler system to indicate if the sprinklers have been activated or extinguishant level monitoring in Gas Extinguishing Systems etc.Module is provided with a loop short-circuit isolator and with up to 3 voltage free single pole change over relay outputs. The output relays are always powered directly from the detection loop. It is not required to use an external 24V DC power supply. Relay operation is confirmed by an onboard Red LED. A 8 way D.I.L. switch is provided to configure the modules address. This value can be set in the range 1 to 125. The following programmable functions are available Input Activation Mode Delayed Input Alarm Activation Output Delayed Activation.Key FeaturesFast Activation ResponseLoop PoweredStatus LEDs for each IO and OPLow Power ConsumptionModule features an integral short-circuit loop isolator

GBP 65.52

1

Global Fire Equipment GFE-IO-1 Addressable 1-Channel IO Module CW Isolator

Global Fire Equipment GFE-IO-1 Addressable 1-Channel IO Module CW IsolatorThe 3 IO PLUS Modules are fully monitored loop powered devices which permit the interfacing of third-party equipment with the FireAlarm Control panel using normally open dry contact connections. Each module can be fitted with a maximum of 3 inputs and 3 outputs. The connection to each input is monitored for fault open or short circuit and alarm conditions.The interface is used to monitor the contacts of an external system which must be interfaced to the Fire Alarm System for example a Flow Switch in a sprinkler system to indicate if the sprinklers have been activated or extinguishant level monitoring in Gas Extinguishing Systems etc.Module is provided with a loop short-circuit isolator and with up to 3 voltage free single pole change over relay outputs. The output relays are always powered directly from the detection loop. It is not required to use an external 24V DC power supply. Relay operation is confirmed by an onboard Red LED. A 8 way D.I.L. switch is provided to configure the modules address. This value can be set in the range 1 to 125. The following programmable functions are available Input Activation Mode Delayed Input Alarm Activation Output Delayed Activation.Key FeaturesFast Activation ResponseLoop PoweredStatus LEDs for each IO and OPLow Power ConsumptionModule features an integral short-circuit loop isolator

GBP 48.43

1

Zeta ZIOU230 Interface Module Loop Powered 5.0A Rating

Zeta ZIOU230 Interface Module Loop Powered 5.0A RatingThe Mains IO Modules are fully monitored loop powered devices which permit the interfacing of third-party equipment with the Fire Alarm Control panel using normally open dry contact connections.The connection to the input is monitored for fault open or short circuit and Alarm conditions.The interface is used to monitor the contacts of an external system which must be interfaced to the Fire Alarm System for example a Flow Switch in a sprinkler system to indicate if the sprinklers have been activated or extinguishant level monitoring in Gas Extinguishing systems etc.Module is provided with a loop short-circuit isolator and with a voltage free single pole change over mains rated output.The output relay is always powered directly from the detection loop. It is not required to use an external 24V DC power supply. Relay operation is confirmed by an on-board red LED. An 8 way D.I.L switch is provided to configure the modules address.This value can be set in the range 1 to 125. The following programmable functions are available Input Activation Mode Delayed Input Alarm Activation Output Delayed Activation.The Simplicity CO 8 range is designed to detect monitor CO concentrations in places such as warehouses car parks tunnels and enclosed buildings where forklifts cars and delivery trucks can produce deadly amounts of carbon monoxide in high traffic areas Carbon Monoxide can accumulate in these areas and can be a serious safety and health concern.Key FeaturesFast Activation ResponseLoop PoweredFive Status LEDs providedLow Power ConsumptionModule features an integral short-circuit loop isolatorSingle mains rated relay contact

GBP 78.77

1

Global Fire GEKKO-2 2 Loop Control Panel

Global Fire GEKKO-2 2 Loop Control PanelThe GEKKO Fire Alarm Control Panel is the successor of the enormously popular GFE JUNIOR panel.The GEKKO can have from 1 to 4 addressable loops. It is housed in a functional ABS plastic enclosure with only two screws used to close and secure the lid.The new graphic backlit LCD display can accommodate any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.It can naturally also communicate with our proprietary ODYSSEY Graphics Interface as well as with third party Building Management Systems through a Modbus output. It is also capable to communicate with a Repeater unit using any of the networking interfaces of the CHAMELEON protocol.Inside the cabinet there is space for installing up to 7 AH 24V DC Sealed Lead Acid backup batteries providing battery supply to the GEKKO and ZEOS associated devices which boast extremely low current consumption.The Cause and Effect programming as well as all customer specific configuration is introduced in the GEKKO using the CHAMELEON CONNECTOR software which is then downloaded to the Flash Memory of the unit.Key Features2 loop panelNetworkable panel compatible with OCTO and NODE range of panelsSupports connection to Repeaters via RS422 Fibre-Optic or TCPIP250 devices per loop 125 address limitUp to 95 VULCAN 2 addressable ultra low current base sounders 32 address limit32 individually programmable sounder addressesFull Self-Addressable Devices support2 Fire output relays change-over and 1 Fault relay NC - opens on fault2 conventional alarm outputs individually programmableBoth detection loops monitored for integrity384 fully programmable zones512 fully programmable sounder groups512 IO groupsEvent log rolling 10000 entriesAvailable only with ZEOS protocolCompatible with all our own low cost ancillary modulesBacklit graphical LCD display of 240x64 pixelsProgramming by integrated keypad or Loader PC softwareMultiple language support menu selectableIntegrated 16 zone LED fire zone indication

GBP 671.47

1

Global Fire VULCAN2-ABIBLK VULCAN 2 Addressable Base Beacon cw Isolator - Black

Global Fire VULCAN2-ABIBLK VULCAN 2 Addressable Base Beacon cw Isolator - BlackThe addressable VULCAN 2 A is available as an Addressable Beacon which may be field configured to operate in either SHADOW or AUXILIARY modes. There are also versions available incorporating a loop isolator. Up to 64 VULCAN 2 A Beacon device can be connected to a single Loop depending on Loop Loading. All VULCAN 2 A devices have dip-switch Address setting while Tone and Mode selection is via a jumper. There is also a potentiometer which may be used to adjust the sound level if required. Normally the VULCAN 2 A will be used in conjunction with a detector however a lid is available as an option for the VULCAN 2 A.Shadow Beacon A Shadow Beacon does not have an individual address thus freeing up addresses for more detection devices. Shadow Beacons do not report back to the control panel so their presence on the Loop is not monitored. Auxiliary Beacon When the VULCAN 2 A is configured as an Auxiliary device it shares the same address as the detector with which it is co-located. When operating in this mode the VULCAN 2 A monitors the Address loop for the command from the control Panel to the detector to illuminate its LED. When this command is received the VULCAN 2 A is also activated.If a Fire is confirmed the remaining sounders may be activated using the Evacuate command. This reduces the inconvenience to other guests in the event of a false alarm while at the same time giving early warning to the occupant of the room in the case of an actual Fire event. Pressing Sounder silence at the panel silences all active sounders. The maximum number of Auxiliary Beacons is 63 and they can be allocated between address 1 and 63.

GBP 61.48

1

Global Fire Vulcan 2 ASBI Addressable White Sounder Beacon with Isolator

Global Fire Vulcan 2 ASBI Addressable White Sounder Beacon with IsolatorThe addressable VULCAN 2 A is available as an Addressable SounderBeacon which may be field configured to operate in either SHADOW or AUXILIARY modes. There are also versions available incorporating a loop isolator. Up to 64 VULCAN 2 A SounderBeacon device can be connected to a single Loop depending on Loop Loading. All VULCAN 2 A devices have dip-switch Address setting while Tone and Mode selection is via a jumper. There is also a potentiometer which may be used to adjust the sound level if required. Normally the VULCAN 2 A will be used in conjunction with a detector however a lid is available as an option for the VULCAN 2 A.Shadow SounderBeacon A Shadow SounderBeacon does not have an individual address thus freeing up addresses for more detection devices. Shadow SounderBeacons do not report back to the control panel so their presence on the Loop is not monitored. Auxiliary SounderBeacon When the VULCAN 2 A is configured as an Auxiliary device it shares the same address as the detector with which it is co-located.When operating in this mode the VULCAN 2 A monitors the Address loop for the command from the control Panel to the detector to illuminate its LED. When this command is received the VULCAN 2 A is also activated. If a Fire is confirmed the remaining sounders may be activated using the Evacuate command. This reduces the inconvenience to other guests in the event of a false alarm while at the same time giving early warning to the occupant of the room in the case of an actual Fire event. Pressing Sounder silence at the panel silences all active sounders. The maximum number of Auxiliary SounderBeacons is 63 and they can be allocated between address 1 and 63.

GBP 50.70

1

Global Fire VULCAN2-ASBIBLK VULCAN 2 Addressable Base Sounder Beacon cw Isolator - Black

Global Fire VULCAN2-ASBIBLK VULCAN 2 Addressable Base Sounder Beacon cw Isolator - BlackThe addressable VULCAN 2 A is available as an Addressable Beacon which may be field configured to operate in either SHADOW or AUXILIARY modes. There are also versions available incorporating a loop isolator. Up to 64 VULCAN 2 A Beacon device can be connected to a single Loop depending on Loop Loading. All VULCAN 2 A devices have dip-switch Address setting while Tone and Mode selection is via a jumper. There is also a potentiometer which may be used to adjust the sound level if required. Normally the VULCAN 2 A will be used in conjunction with a detector however a lid is available as an option for the VULCAN 2 A.Shadow Beacon A Shadow Beacon does not have an individual address thus freeing up addresses for more detection devices. Shadow Beacons do not report back to the control panel so their presence on the Loop is not monitored. Auxiliary Beacon When the VULCAN 2 A is configured as an Auxiliary device it shares the same address as the detector with which it is co-located. When operating in this mode the VULCAN 2 A monitors the Address loop for the command from the control Panel to the detector to illuminate its LED. When this command is received the VULCAN 2 A is also activated.If a Fire is confirmed the remaining sounders may be activated using the Evacuate command. This reduces the inconvenience to other guests in the event of a false alarm while at the same time giving early warning to the occupant of the room in the case of an actual Fire event. Pressing Sounder silence at the panel silences all active sounders. The maximum number of Auxiliary Beacons is 63 and they can be allocated between address 1 and 63.

GBP 79.55

1

Global Fire Equipment VULCAN2-ABI Vulcan 2 ABI Addressable Base Beacon with Isolator

Global Fire Equipment VULCAN2-ABI Vulcan 2 ABI Addressable Base Beacon with IsolatorThe addressable VULCAN 2 A is available as an Addressable Beacon which may be field configured to operate in either SHADOW or AUXILIARY modes. There are also versions available incorporating a loop isolator. Up to 64 VULCAN 2 A Beacon devices can be connected to a single Loop depending on Loop Loading. All VULCAN 2 A devices have dip-switch Address setting while Tone and Mode selection is via a jumper. There is also a potentiometer which may be used to adjust the sound level if required. Normally the VULCAN 2 A will be used in conjunction with a detector however a lid is available as an option for the VULCAN 2 A.Shadow Beacon A Shadow Beacon does not have an individual address thus freeing up addresses for more detection devices. Shadow Beacons do not report back to the control panel so their presence on the Loop is not monitored. Auxiliary Beacon When the VULCAN 2 A is configured as an Auxiliary device it shares the same address as the detector with which it is co-located. When operating in this mode the VULCAN 2 A monitors the Address loop for the command from the control Panel to the detector to illuminate its LED. When this command is received the VULCAN 2 A is also activated.If a Fire is confirmed the remaining sounders may be activated using the Evacuate command. This reduces the inconvenience to other guests in the event of a false alarm while at the same time giving early warning to the occupant of the room in the case of an actual Fire event. Pressing Sounder silence at the panel silences all active sounders. The maximum number of Auxiliary Beacons is 63 and they can be allocated between address 1 and 63.

GBP 40.98

1

Global Fire GEKKO-0 Loop Control Panel

Global Fire GEKKO-0 Loop Control PanelThe GEKKO Fire Alarm Control Panel is the successor of the enormously popular GFE JUNIOR panel.The GEKKO can have from 1 to 4 addressable loops. It is housed in a functional ABS plastic enclosure with only two screws used to close and secure the lid.The new graphic backlit LCD display can accommodate any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.It can naturally also communicate with our proprietary ODYSSEY Graphics Interface as well as with third party Building Management Systems through a Modbus output. It is also capable to communicate with a Repeater unit using any of the networking interfaces of the CHAMELEON protocol.Inside the cabinet there is space for installing up to 7 AH 24V DC Sealed Lead Acid backup batteries providing battery supply to the GEKKO and ZEOS associated devices which boast extremely low current consumption.The Cause and Effect programming as well as all customer specific configuration is introduced in the GEKKO using the CHAMELEON CONNECTOR software which is then downloaded to the Flash Memory of the unit.Key Features1 to 4 loops panelNetworkable panel compatible with OCTO and NODE range of panelsSupports connection to Repeaters via RS422 Fibre-Optic or TCPIP250 devices per loop 125 address limitUp to 95 VULCAN 2 addressable ultra low current base sounders 32 address limit32 individually programmable sounder addressesFull Self-Addressable Devices support2 Fire output relays change-over and 1 Fault relay NC - opens on fault2 conventional alarm outputs individually programmableBoth detection loops monitored for integrity384 fully programmable zones512 fully programmable sounder groups512 IO groupsEvent log rolling 10000 entriesAvailable only with ZEOS protocolCompatible with all our own low cost ancillary modulesBacklit graphical LCD display of 240x64 pixelsProgramming by integrated keypad or Loader PC softwareMultiple language support menu selectableIntegrated 16 zone LED fire zone indication

GBP 388.99

1

Global Fire Equipment GEKKO-2BLK GEKKO 2 Loop Control Panel Anthracite

Global Fire Equipment GEKKO-2BLK GEKKO 2 Loop ControlPanel AnthraciteThe GEKKO Fire Alarm Control Panel is the successor to GFEswell-known JUNIOR V4 panel.The GEKKO can have from 1 to 4 addressable loops. It ishoused in a functional ABS plastic enclosure with only two screws used toclose and secure the lid.The new graphic backlit LCD display can accommodate any typeof custom characters or graphic symbols allowing multi-language support aswell as visual and customisable elements.It can communicate with our proprietary ODYSSEY GraphicsInterface as well as with third party Building Management Systems through aModbus output. It is also capable of communicating with a repeater unit usingany of the networking interfaces of the CHAMELEON protocol.Inside the cabinet there is space to install up to 7 AH 24VDC Sealed Lead Acid backup batteries providing battery supply to the GEKKO andZEOS associated devices which boast extremely low energy consumption.The Cause and Effect programming as well as allcustomer-specific configuration is introduced in the GEKKO using the CHAMELEONCONNECTOR software which is then downloaded to the flash memory of the unit.Key FeaturesSuccessor to GFEs JUNIOR V4 panel1 to 4 loop panel 2 loop cards installedSupports connection to Repeaters via RS422 Fibre-Optic orTCPIPNetworkable panel compatible with OCTO and NODE range ofpanelsUp to 250 devices per loop only 125 addresses availableUp to 95 VULCAN 2 addressable ultra low current basesounders 32 address limit32 individually programmable sounder addressesFull self-addressable devices support2 Fire output relays change-over and 1 fault relay NC -opens on fault2 conventional alarm outputs Individually programmableBoth detection loops monitored for integrity512 fully programmable sounder and IO groups384 fully programmable zonesEvent log rolling 10000 entriesAvailable only with ZEOS protocolCompatible with all GFE manufactured ancillary modulesBacklit graphical LCD display of 240x64 pixelsProgramming by integrated keypad or Loader PC softwareMultiple language support menu selectableIntegrated 16 zone LED fire zone indicationEN54-13 EN54-2 EN54-4 1328-CPR-0737 certified