stavblender med piskeris from GBP 3 | See the cheapest prices and offers on css.nordicadpartner.dk

Hochiki Marine Sensor Mounting Base YBN-R3MWHT

Hochiki Marine Sensor Mounting Base YBN-R3MWHTModel YBN-R3M is a Common Mounting Base which is fully compatible with Hochikis Marine Approved ESP sensors. It is supplied with square cable clamps for secure and reliable cable termination and is also capable of driving a remote LED if requiredKey FeaturesElectronics freeSupports the ESP Marine Approved SensorsStainless steel contactsTakes 2.5 mm cablesSlim profile - only 8 mmRugged wiring contactsFacility for remote indicatorQuick Connection via square cable clampsApproved to MED by GL

GBP 3.36

1

Hochiki Marine Common Mounting Base YBN-R3M

Hochiki Marine Common Mounting Base YBN-R3MModel YBN-R3 is a Common Mounting Base which is fully compatible with Hochikis Marine Approved ESP sensors. It is supplied with square cable clamps for secure and reliable cable termination and is also capable of driving a remote LED if required.Key FeaturesElectronics freeSupports the ESP Marine Approved SensorsStainless steel contactsTakes 2.5 mm cablesSlim profile - only 8 mmRugged wiring contactsFacility for remote indicatorQuick Connection via square cable clampsApproved to MED by GL

GBP 3.36

1

Hochiki WCP1A Marine Conventional Weatherproof Call Point

Hochiki WCP1A Marine Conventional Weatherproof Call PointTheWCP1A is a Conventional marine-approved weather-proof call-point based upon the industry standard KAC World Series housing and features easy to install push-fit wiring terminals.The unit can support either a Frangible Glass element or a Non Frangible Plastic element and features a weather-proof Housing to IP67 which means it can be mounted in the most severe environmental conditions without water ingress.Key FeaturesApproved to EN54-112001Terminals can accommodate up to a 2.5 mm solid conductorIngress Protection rated to IP67Approved to MED by GLGL Type ApprovalApproved by LPCB

GBP 95.89

1

Hochiki CHQ-DIM2MSCI Marine Dual Input Module with SCI

Hochiki CHQ-DIM2MSCI Marine Dual Input Module with SCIModel CHQ-DIM2MSCI is a Marine Approved Dual Input Module designed to interface to a variety of inputs such as door contacts sprinkler flowdoor switches and plant equipment. Also features an integral short-circuit isolator.A back box is also available CHQ-BACKBOX which when used in conjunction with the CHQ-DIM2MSCI increases the IP rating to IP65.Key FeaturesSingle Loop AddressLoop Powered2 Independent Inputs for Monitoring of Volt Free ContactsEach Input can be Configured to Monitor either Normally Open or Normally Closed contactsSmart-Fix Housing System for flexibilityFeatures an integral SCIApproved to MED by GLGL Type ApprovalApproved by LPCB

GBP 62.12

1

Hochiki Marine Approved Combined Heat Detector DCD-CE3M

Hochiki DCD-CE3M Marine Approved Combined Heat DetectorThe DCD-CE3M is a Marine Approved Rate of Rise Heat Detector with a 90C fixed temperature element using a thermistor and linearising circuit to provide an accurate linear response Heat Detector.The DCD-CE3M is ideal for use where medium ambient temperatures exist such as drying rooms or where Smoke Detectors are unsuitable because of the presence of steam or cooking fumes such as in a kitchengalley.The DCD-CE3M is supported on the majority of conventional systems. A third terminal provides remote indicator output.Key FeaturesElectronic linear heat detectionRemote Indicator outputWide voltage range 9.5 30 V dcTwin fire LEDs allow 360 degree viewingApproved by LPCBApproved to MED by GLGL Type approval

GBP 24.29

1

Hochiki Marine Conventional Combined Heat Detector DCD-AE3M

Hochiki DCD-AE3M Marine Conventional Combined Heat DetectorThe DCD-AE3M is a Marine Approved Rate of Rise Heat Detector with a 60C fixed temperature element using a thermistor and linearising circuit to provide an accurate linear response Heat Detector. The DCD-AE3M is ideal for use where medium ambient temperatures exist such as drying rooms or where Smoke Detectors are unsuitable because of the presence of steam or cooking fumes such as in a kitchengalley.The DCD-AE3M is supported on the majority of conventional systems. A third terminal provides remote indicator output.Key FeaturesElectronic linear heat detectionRemote indicator outputWide voltage range 9.5 30 V dcTwin fire LEDs allow 360 degree viewingApproved by LPCBApproved to MED by GLGL Type approval

GBP 24.29

1

Hochiki Marine Standard Ivory Mounting Base YBN-R6M

Hochiki Marine Standard Ivory Mounting Base YBN-R6MModel YBN-R6M is a Conventional Detector Mounting Base approved for marine applications by GL Germanischer Lloyd and is associated with the CDX Range of Marine Approved Detectors.It is supplied with square cable clamps for secure and reliable cable termination but the base does not provide line continuity during detector removal therefore if Call Points are being used then these should be wired onto the zone first. The integrated third terminal provides remote indicator output.Key FeaturesIntegral remote indicator outputLow Profile only 8 mmRugged designElectronics freeQuick connections via square cable clampsAccepts 2.5 mm cablesBayonet slot low insertion force for detectorsApproved to MED by GLGL Type approval

GBP 4.99

1

Hochiki Marine Photoelectric Smoke Sensor White ALN-ENMWHT

Hochiki ALN-ENMWHT Marine Photoelectric Smoke Sensor WhiteModel ALN-ENMWHT is a Marine Approved Photoelectric White Smoke Sensor which is fully compatible with Hochikis ESP Analogue Addressable Protocol.The ALN-ENM incorporates Hochikis newest High Performance Chamber Technology removing the need to use Ionisation Smoke Sensors in the majority of applications. This also allows the sensor threshold level to be increased thereby improving the signal to noise ratio and reducing susceptibility to false alarms.The ALN-ENM smoke chamber is easily removed or replaced for cleaning and utilises a unique improved baffle design which allows smoke to enter the chamber whilst keeping out ambient light.Key FeaturesApproved to MED by GLRemovable High Performance chamberTwin LEDs allow 360 viewing green when polling red in fireLocking mechanism sensor to baseVariable sensitivityElectronically addressedPulsingnon-pulsing controlled from panelApproved by LPCB VdS

GBP 42.62

1

Hochiki Marine Dual Sounder Controller with SCI CHQ-DSC2MSCI

Hochiki CHQ-DSC2MSCI Marine Dual Sounder Controller with SCIThe CHQ-DSC2MSCI is a Marine Approved Dual Sounder Controller which has been designed to provide two sounder outputs that can be driven separately with full fault monitoring. The monitored input can be used for local power supply fault monitoring or as a general-purpose input.The unit utilises simple DIL switches for reliable addressing. A back box is also available CHQ-BACKBOX which when used in conjunction with the CHQ-DSC2MSCI increases the IP rating to IP65.Key FeaturesSingle loop addressEach alarm circuit fused at 1 ampTwo independent sounder circuits each fully monitored for open and short circuit faultsAuxiliary monitored inputOutputs can be driven continuously or synchronised pulsed sounder driveSmart-Fix housing system for flexibilityFeatures an integral SCIApproved to MED by GLGL Type approvalApproved by LPCB

GBP 111.84

1

Hochiki Marine Single Zone Monitor with SCI CHQ-SZM2MSCI

Hochiki CHQ-SZM2MSCI Marine Single Zone Monitor with SCIThe CHQ-SZM2MSCI is a Marine Approved Single Zone Monitor designed to allow up to 6 marine approved conventional detectors to be interfaced to Hochikis ESP analogue addressable system. The unit also features an integral short-circuit isolator.The CHQ-SZM2MSCI utilises simple DIL switches for reliable addressing. A back box is also available CHQ-BACKBOX which when used in conjunction with the CHQ-SZM2MSCI increases the IP rating to IP65.Key FeaturesLoop Powered with Single Loop AddressUp to 6 Conventional DetectorsRemote LED OutputFully Monitored for Short and Open Circuit FaultsSmart-Fix Housing System for flexibilityFeatures an integral SCIApproved to MED by GLGL Type approvalApproved by LPCBPlease Note The conventional zone on the CHQ-SZM2MSCI does not support any line continuity options if Call Points are being interfaced they should be wired at the beginning of the zone.

GBP 68.87

1

Hochiki CHQ-DRC2MSCI Marine Approved Dual Relay Controller With SCI

Hochiki CHQ-DRC2MSCI Marine Approved Dual Relay Controller With SCIThe CHQ-DRC2MSCI is a Marine Approved Dual Relay Controller module designed to provide two general-purpose relay outputs each output can be driven separately for control of such devices as dampers or for control of plant and equipment shutdown. The monitored input can be used for local power supply fault monitoring or as a general-purpose input.The unit also features an integral short-circuit isolator. The CHQ-DRC2MSCI utilises simple DIL switches for reliable addressing. A back box is also available CHQ-BACKBOX which when used in conjunction with the CHQ-DRC2MSCI increases the IP rating to IP65.Key FeaturesApproved to MED by DNVLoop powered with single loop addressProvides 2 Independently controlled changeover relaysRelays contact rated at 30 VDC at 1 AAuxiliary monitored inputFeatures an integral SCICan be used with CHQ-BACKBOX to comply with BS 7671SIL2 and Railway Approved variants available

GBP 83.29

1

Hochiki Marine Conventional Infrared Flame Detector DRD-EM

Hochiki DRD-EM Marine Conventional Infrared Flame DetectorThe DRD-EM is a marine-approved flame detector designed for internal use to detect large flames. The detector fits the CDX marine-approved standard mounting base YBN-R6M. The detection zone is a 90 cone and the detection range is up to and including 25 m.The flame detector is designed for use where open flaming fires may be expected. It responds to the light emitted from flames during combustion. The detector discriminates between flames and other light sources by responding only to particular optical wavelengths and flame flicker frequencies. This enables the detector to avoid false alarms due to such factors as flickering light sources.The DRD-E detector can detect IR radiated from flames. Flames radiated from a fire have an IR peak emission of 4.3um occurring during the CO2 formation due to the combustion of hydrocarbons from 2 to 15 Hz.Key FeaturesClass 1 performance as defined in BS EN54-102002 range up to 25 mSingle IR technologyRobust and slim designLow current consumptionEasy to installFits the CDX marine-approved standard baseTwin LEDs for 360 viewApproved by LPCB VdSApproved to MED by GLSIL Level 2 approved variantsApplicationsCoal handling plantAircraft hangarsAutomotive industry - spray booths parts manufacturePharmaceuticalEngine roomsWaste handlingPower plantsTransformer stationsPetrochemical

GBP 427.88

1

Hochiki HCP-WMSCI Addressable Marine Weatherproof Call Point with SCI

Hochiki HCP-WMSCI Addressable Marine Weatherproof Call Point with SCIThe HCP-WMSCI is a weatherproof Manual Call Point with integral short-circuit isolator which is fully compatible with Hochikis ESP analogue addressable protocol. The unit incorporates a bi-coloured LED which can be selected as pulsingnon-pulsing 1 for communications polling and is continuously lit when the HCP-WMSCI is operated in these two states the LED will show red. The LED will show amber when a short-circuit is present but will switch to red if the unit is activated.The unit operates by pressing the EN54 compliant non-frangible plastic element and produces a high level ESP interrupt. A built in test function initiated by the control panel ensures the integrity of the device at all times and the device can be tested by insertion of a test key in the underside of the unit. Two terminal blocks are provided for easy connection to the loop wiring. The unit is addressed using the TCH-B200 Hand Held Programmer for quick and reliable addressing. An optional glass element is also available.Key FeaturesFast responseIntegral short-circuit isolatorBi-coloured status LEDNon-frangible element fitted as standard conforms to EN54Addressed with TCH-B200 Hand Held ProgrammerSurface mountedIP67 ratedLPCB approved to EN54GL and MED Type approval

GBP 162.67

1

Hochiki Addressable Marine Call Point with SCI HCP-EMSCI

Hochiki HCP-EMSCI Addressable Marine Call Point with SCIThe HCP-EMSCI is a Manual Call Point with integral short-circuit isolator which is fully compatible with Hochikis ESP analogue addressable protocol. The unit incorporates a bi-coloured LED which can be selected as pulsingnon-pulsing1 for communications polling and is continuously lit when the unit is operated in these two states the LED will show red. The LED will show amber when a short-circuit is present but will switch to red if the unit is activated.The unit operates by pressing the EN54 compliant non-frangible plastic element and produces a high-level ESP interrupt. A built-in test function initiated by the control panel ensures the integrity of the device at all times and the device can be tested by insertion of a test key in the underside of the unit. Two terminal blocks are provided for easy connection to the loop wiring.The unit is addressed using the TCH-B200 Hand Held Programmer for quick and reliable addressing. The unit can be flush mounted as supplied. For surface fixing a suitable back box such as the SR MOUNTING BOX is required sold separately. An optional glass element is also available.Key FeaturesApproved to MED by GLSIL Level 2 approved variant availableIdeal for use in oil and gas environmentsFast responseIntegral short-circuit isolatorBi-coloured status LEDNon-frangible element fitted as standard conforms to EN54Addressed with TCH-B200 Hand Held ProgrammerSurface or flush mounting if surface mounting requires SR MOUNTING BOX sold separatelyLPCB Approved to EN54

GBP 44.60

1

Vores kunder ligger øverst på Google

Google Ads Specialister fra Vestjylland

Brand

Merchant

Price (EUR)