Vores kunder ligger øverst på Google

Google Ads Specialister fra Vestjylland

Vi er 100% dedikerede til Google Annoncering – Vi har mange års erfaring med Google Ads og den bruger vi på at opsætte, optimere & vedligeholde vores fantastiske kunders konti.

100% Specialiseret i Google Ads
Vi har mange års erfaring fra +300 konti
Ingen lange bindinger & evighedskontrakter
Jævnlig opfølgning med hver enkelt kunde
Vi tager din virksomhed seriøst
KONTAKT OS
LÆS UDTALELSER & SUCCESHISTORIER

3 results (0,13499 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Advanced MxPro MXP-542 24VDC - 24VDC Convertor Isolator

Advanced MxPro MXP-542 24VDC - 24VDC Convertor Isolator

Advanced MxPro MXP-542 24VDC - 24VDC Convertor IsolatorA 24VDC - 24VDC Convertor Isolator for use with Mxp-631 Fib.The Mxp-631 media converters are equipped with a multiple interface circuit that can handle RS-232 or RS-422485 serial interfaces and multi-mode or single-mode fiber. Mxp-631 converters are used to extend serial transmission up to 5km Mxp-631-MM with multi-mode fiber or up to 40km Mxp-631-SM with single-mode fiber. The Mxp-631 converters can be configured to convert either RS-232 signals or RS422485 signals but not both at the same time.The Mxp-631 converters can automatically detect the serial baudrate. This is an extremely convenient feature. Even if a devices baudrate is changed the signal will still be transmitted through the media converter without any data loss.The Mxp-631 converters can be used to connect serial devices to a fiber ring. To form the ring connect to the Tx port of one Mxp-631 to the Rx port of a neighbouring converter. Once the ring is set up simply use the DIP switches to configure the Mxp-631 converters for ring mode. When one node transmits a signal the signal travels around the ring until it returns back to the transmitting unit which then blocks the signal. With the Mxp-631 you can set up fiber rings that have a total circumference of up to 100km.ADDC is a patented hardware data flow solution to handle RS-485 data direction control. ADDC senses and controls RS-485 data direction automatically making it unnecessary to use the hand shaking signal.Key FeaturesExtends RS-232422485 transmission up to40 km with single-mode - Mxp-631-SM5 km with multi-mode - Mxp-631-MMCompact sizeProtects against electrical interference and chemical corrosionSupports baudrates of 50 bps to 921.6 KbpsWide temperature models available -40 to 75CPlease note this way of communication is not EN54 approved.

GBP 129.11
1

Advanced MXP-509 Fault Tolerant Network Card MxPro 5

Advanced MXP-509 Fault Tolerant Network Card MxPro 5

Advanced MXP-509 Fault Tolerant Network Card MxPro 5The Ad-NeT network system allows all MxPro 5 series control panels remote terminals and network peripherals to be connected together using standard fire resistant two-core cable. It provides both the benefits of distributed intelligence and reduced installation costs whilst catering for the smallest two-panel network through to the largest 200 panel wide area networked system.The network operates as a true peer-to peer system allowing information from any input or output device to be passed over the network and displayed on any MxPro 5 control panel or remote terminal as required.Simply adding and connecting a network card allows any MxPro 5 control panel or remote terminal to be networked. All other nodes on the Ad-NeT system will be instantly aware of a panel as soon as it is given a valid network node address allowing additional panels to be added at any time. All panels incorporate a network analyser providing valuable diagnostic and status information and also have the facility to prevent the transmission of fires or faults during commissioning.For more complex systems the Windows based PC-NeT Mx configuration software allows sector-based programming for Mute Silence Resound and Reset control keys as well as investigation delays group disablement and test instructions. All panels within the same sector will share common controls and each panel or remote terminal can also be programmed to show specific network information on a zonal basis. For cause and effect any input device can be programmed to operate any output device on any panel.Key FeaturesLarge Ad-NeT 200 Panel NetworkUp to 1.5Km between Control PanelsWindows based PC setupNetwork Systems share up to 1000 zonesNetwork Analysis from Control PanelStandard NetworkThe maximum total cable length is 1.5km. The maximum number of network nodes is 32 50 with signal bufferFault Tolerant NetworkThe maximum cable length is 1.5km between each node and the maximum total loop length is 20km. Each network card has in-built diagnostics and is fully monitored for both short and open circuit faults between nodes. The network is capable of withstanding a single fault between nodes without loss of communications to any single panel. The maximum number of network nodes is 200.

GBP 584.40
1

Advanced MXP-503 Standard Network Card MxPro5

Advanced MXP-503 Standard Network Card MxPro5

Advanced MXP-503 Standard Network Card MxPro5The Ad-NeT network system allows all MxPro5 series control panels remote terminals and network peripherals to be connected together using standard fire resistant two-core cable. It provides both the benefits of distributed intelligence and reduced installation costs whilst catering for the smallest two-panel network through to the largest 200 panel wide area networked system.The network operates as a true peer-to peer system allowing information from any input or output device to be passed over the network and displayed on any MxPro5 control panel or remote terminal as required.Simply adding and connecting a network card allows any MxPro5 control panel or remote terminal to be networked. All other nodes on the Ad-NeT system will be instantly aware of a panel as soon as it is given a valid network node address allowing additional panels to be added at any time. All panels incorporate a network analyser providing valuable diagnostic and status information and also have the facility to prevent the transmission of fires or faults during commissioning.For more complex systems the Windows based PC-NeT Mx configuration software allows sector-based programming for Mute Silence Resound and Reset control keys as well as investigation delays group disablement and test instructions. All panels within the same sector will share common controls and each panel or remote terminal can also be programmed to show specific network information on a zonal basis. For cause and effect any input device can be programmed to operate any output device on any panel.Key FeaturesLarge Ad-NeT 200 Panel NetworkUp to 1.5Km between Control PanelsWindows based PC setupNetwork Systems share up to 1000 zonesNetwork Analysis from Control PanelStandard NetworkThe maximum total cable length is 1.5km. The maximum number of network nodes is 32 50 with signal bufferFault Tolerant NetworkThe maximum cable length is 1.5km between each node and the maximum total loop length is 20km. Each network card has in-built diagnostics and is fully monitored for both short and open circuit faults between nodes. The network is capable of withstanding a single fault between nodes without loss of communications to any single panel. The maximum number of network nodes is 200.

GBP 234.06
1