new balance foam hierro v6 gtx from GBP 0 | See the cheapest prices and offers on css.nordicadpartner.dk

Apollo New Manual Call Point Reset Keys - Pack of 10 44251-176APO

Apollo New Manual Call Point Reset Keys Pack of 10 44251-176APOA pack of Manual Call Point Reset Keys for the new range of Apollo manual call points.They allow the user to perform a manual test on the call point to test for correct operation.Key FeaturesPack of 10Ergonomically designedAllows the user to test and reset Apollo call points1 year warranty

GBP 7.06

1

Apollo Blank XPert Card for XPander Wireless Range - White 29600-413

Apollo Blank XPert Card for XPander Wireless Range - White 29600-413The 29600-413 is a spare singular blank XPERT card in white which has been designed for use with the XPander range. XPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop.XPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesSimplifies and speeds up installation and commissioningAddress remains the same no matter how often detectors are replacedUses patented proven technologyFlexibility to create any address

GBP 0.20

1

Apollo Orbis I.S. Timesaver Base ORB-MB-50018-APO

Apollo Orbis I.S. Timesaver Base ORB-MB-50018-APOThe Orbis IS TimeSaver Base is a completely new design that provides installers with an open working area with fixing holes shaped to allow a simple mounting procedure.It is important that the Orbis I.S. detectors be installed in such a way that all terminals and connections are protected to at least IP20 when the detector is in the base. Special care must be taken with the rear of the mounting base where live metal parts may be accessible. Flush mounting of the base on a flat surface will provide the required degree of protection.Key FeaturesGrouped terminals to make wiring easyTwo fixing centresLED alignment markDetector locking mechanism

GBP 8.21

1

Apollo Soteria Optical Smoke Detector Isolated SA5100-600

Apollo Soteria Optical Smoke Detector Isolated SA5100-600TheSOTERIA Optical Detector uses new optical sensing technology PureLight to detect smoke particles entering the chamber. PureLight marks a new stage in the development of Apollo optical technology and aims to reduce the possibility of false alarms and to increase the reliability of detection of a real fire.Backwards CompatibilitySoteria detectors have been designed to operate on XP95 and Discovery loops. This allows for Soteria detectors and bases to operate on existing systems and for Soteria detectors to operate on XP95 and Discovery bases XPERT 7 Intelligent Mounting Base. It should be noted that not all features of Soteria will be available when used with XP95 or Discovery fire control panels.If Soteria detectors are used with XP95 fire control panels incorporating drift compensation algorithms these must be disabled when communicating with Soteria devices. When Soteria detectors are used with an XPERT 7 Intelligent Mounting Base on a CoreProtocol system Soteria devices will have a 128 address offset due to only 7 address pips being available on the XPERT 7 card. For example an XPERT 7 card set at 32 will address as 160 on CoreProtocol with Soteria detectors.Key FeaturesPureLight optical technology reduces false alarms and enhances smoke recognitionUtilises digital CoreProtocol communicationsCompatible with XP95 and Discovery systemsCompatible with existing fire control panelsMechanically compatible with existing basesAvailable with or without integrated switchable isolatorDrift compensationTri-coloured LED status indicatorPolycarbonate moulding for colour stability and strengthComprehensively tested to exceed EN 54-7 standardFasTest for quicker testing of detectorsXPERT card addressing or auto addressingLocking mechanism grub screwPlease Note not all features are available when SOTERIAdevices are connected to an XP95 or Discovery fire control panel.

GBP 41.20

1

Apollo SA4700-100APO Intelligent Switch Monitor

Apollo SA4700-100APO Intelligent Switch MonitorThe Intelligent Switch Monitor is designed to monitor thestate of one or more single pole volt-free contacts connectedon a single pair of cables to report the status. It has a selectable status reporting delay making it suitable for monitoring flowswitches. Compatible with XP95 Discovery and CoreProtocol digital communication protocols.Mechanical ConstructionThe Intelligent Switch Monitor is available in the new faceplate style enclosure. This can be mounted with the supplied back-box for surface mounting or flush mounted using a UK double gang flush mounting back-box of minimum depth 30mm.Key FeaturesImproved design for ease of wiring meaning faster installationContains controllable isolatorAddress range 1 - 254Five pre-configured modes including compatibility mode from XP95Discovery to CoreProtocol systemsPriority mode for fast responseConfigurable input stylesEarth fault monitoring

GBP 46.70

1

Apollo Blank XPert Card for XPander Wireless Range -Red 29600-399

Apollo Blank XPert Card for XPander Wireless Range RedSpare singular blank XPERT card in red for the XPander range. XPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop.XPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Brand Featuresmodern styling loop-powered interface operating on 868MHz wireless addresses seen by control panel as normal addresses radio base with wireless circuitry and battery compartment chamber designed to inhibit dirt penetration and thus reduce false alarms automatic drift compensation with DirtAlert warning algorithms for transient alarm rejection FasTest reduces time taken to test detectors remote test facility 3-5 years battery lifeProduct InformationAddress card supplied with all bases. Using a coding guide pips are removed to set the address of the inserted device.Key FeaturesSimplifies and speeds up installation and commissioningAddress remains the same no matter how often detectors are replacedUses patented proven technologyFlexibility to create any address

GBP 0.24

1

Apollo XP95 Mini Switch Monitor - 55000-760APO

Apollo XP95 Mini Switch Monitor - 55000-760APOThe Mini Switch Monitor is an interface within an entirely new housing. Designed in response to customer feedback thesmaller Mini Switch Monitor can be fitted onto a 35mm DIN-Rail with a twist-click motion or mounted in an enclosure such as a manual call point.It is designed to monitor the state of one or more single pole volt free contacts connected to a single pair of cables and to report the status to Apollo compatible control equipment.The monitor is designed to fit into equipment with limited space or to be mounted within an enclosure such as a manual call point. The interrupt feature means the monitor can be used where a priority response is required in particular for monitoring an individual or a cone of conventional manual call points.

GBP 42.22

1

Apollo SA4700-102APO Intelligent Input Output Unit

Apollo SA4700-102APO Intelligent Input Output UnitThe Intelligent InputOutput Unit provides supervision of oneor more normally open contacts connected to a single pair ofcables and a set of changeover relay output contacts. Compatible with XP95 Discovery and CoreProtocol digital communication protocols.Mechanical ConstructionThe Intelligent InputOutput Unit is available in the new faceplate style enclosure. This can be mounted with the supplied back-box for surface mounting or flush mounted using a UK double gang flush mounting back-box of minimum depth 30mm.OperationThe Intelligent InputOutput Unit provides supervision of one or more normally open contacts connected to a single pair of cables and a set of changeover relay output contacts.Key FeaturesImproved design for ease of wiring meaning faster installationContains controllable isolatorAddress range 1 - 254Nine pre-configured modes including compatibility mode from XP95Discovery to CoreProtocol systemsFailsafe mode meets BS 7273-4 requirementsConfigurable input stylesEarth fault monitoring

GBP 55.15

1

Apollo SA4700-104APO Intelligent Twin Input Output Unit

Apollo SA4700-104APO Intelligent Twin Input Output UnitThe Intelligent Twin InputOutput Unit provides the functionof two InputOutput Units within one enclosure. The twounits are electrically independent of each other. There is a DILswitch on each unit to set the address.Both inputoutput units in the enclosure provide supervisionof one or more normally open volt free contacts connectedto a single pair of cables and a set of changeover relay outputcontacts. Compatible with XP95 Discovery and CoreProtocol digital communication protocols.Mechanical ConstructionThe Intelligent Twin InputOutput Unit is available in the new faceplate style enclosure. This can be mounted with the supplied backbox for surface mounting or flush mounted using a UK double gang flush mounting back-box of minimum depth 30mm.Key FeaturesImproved design for ease of wiring meaning faster installationContains controllable isolatorAddress range 1 - 254Nine pre-configured modes including compatibility mode from XP95Discovery to CoreProtocol systemsFailsafe mode meets BS 7273-4 requirementsConfigurable input stylesEarth fault monitoring

GBP 77.62

1

Apollo SA6700-100APO Intelligent Twin Switch Monitor

Apollo SA6700-100APO Intelligent Twin Switch MonitorThe Intelligent Twin Switch Monitor provides the functionof two Switch Monitor units within one enclosure. The two units are electrically independent of each other. There is a DILswitch on each unit to set the address.Both Switch Monitor units in the enclosure are designed tomonitor the state of one or more single pole volt-free contactsconnected on a single pair of cables to report the status. Ithas a selectable status reporting delay making it suitable formonitoring flow switches. Compatible with XP95 Discovery and CoreProtocol digital communication protocols.ConstructionThe Intelligent Twin Switch Monitor is available in the new faceplate style enclosure. This can be mounted with the supplied back-box for surface mounting or flush mounted using a UK double gang flush mounting back-box of minimum depth 30mm.Key FeaturesImproved design for ease of wiring meaning faster installationContains controllable isolatorAddress range 1 - 254Five pre-configured modes including compatibility mode from XP95Discovery to CoreProtocol systemsPriority mode for first responseConfigurable input stylesEarth fault monitoring

GBP 65.76

1

Apollo XPander Combined Sounder Base XPA-WB-14036-APO

Apollo XPander Combined Sounder BaseXPA-WB-14036-APOThe XPander Combined Sounder and Detector is wireless and designed to provide one-point detection and notification.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesWirelessAvailable with a choice of XPander detectorsBi-directional monitored radio platformA choice of four tone pairsCertified to EN 54-25

GBP 318.79

1

Apollo XPander Combined Sounder Beacon Base XPA-WB-14037-APO

Apollo XPander Combined Sounder Beacon BaseXPA-WB-14037-APOThe XPander Combined Sounder and Detector is wireless and designed to provide one-point detection and notification.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesWirelessAvailable with a choice of XPander detectorsBi-directional monitored radio platformA choice of four tone pairsCertified to EN 54-25

GBP 368.42

1

Apollo XPA-MC-14101-APO XPander Manual Call Point - Integral Radio Base

Apollo XPA-MC-14101-APO XPander Manual Call Point - Integral Radio BaseThe XPander Manual Call Point is compliant with EN 54-11 and is a wireless device.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Please note The image is for illustrative purposes only.

GBP 164.53

1

Apollo XPander Manual Call Point Integral Radio Base - XPA-MC-14006-APO

Apollo XPander Manual Call Point Integral Radio Base XPA-MC-14006-APOThe XPander Manual Call Point is compliant with EN 54-11. It is wireless and is powered by two independent packs of three AA alkaline batteries with a typical five year life.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesWirelessXPERT addressingResettable elementFast response reports an alarm in under one secondLED to indicate operation

GBP 131.14

1

Apollo XPander Wireless Sounder Base amp CS Heat Detector - XPA-CB-14018-APO

Apollo XPander Wireless Sounder Base CS Heat Detector - XPA-CB-14018-APOThe XPander Combined Sounder and Detector is a wireless and designed to provide one point notification and detection.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key Features WirelessAvailable with a choice of XPander detectorsBi-directional monitored radio platformA choice of 4 tone pairsCertified to EN54 Part 25

GBP 335.20

1

Apollo XPander Wireless Sounder Base amp Optical Smoke Detector - XPA-CB-14016-APO

Apollo XPander Wireless Sounder Base Optical Smoke Detector - XPA-CB-14016-APOThe XPander Combined Sounder and Detector is a wireless and designed to provide one point notification and detection.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key Features WirelessAvailable with a choice of XPander detectorsBi-directional monitored radio platformA choice of 4 tone pairsCertified to EN54 Part 25

GBP 328.32

1

Apollo XPander 868MHz Diversity Survey Kit XPA-TE-14075-APO

Apollo XPander 868MHz Diversity Survey Kit XPA-TE-14075-APOThe XPander Diversity Survey kit is used at the site survey stage to ascertain if a site is suitable for an XPander installation. A site survey must be carried out before XPander can be installed. The Diversity Survey Kit is compliant to BS 5839-1.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesIndicates the suitability of proposed device location

GBP 369.71

1

Apollo XPander Wireless Sounder Base amp A1R Heat Detector - XPA-CB-14017-APO

Apollo XPander Wireless Sounder Base A1R Heat Detector - XPA-CB-14017-APOThe XPander Combined Sounder and Detector is a wireless and designed to provide one point notification and detection.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key Features WirelessAvailable with a choice of XPander detectorsBi-directional monitored radio platformA choice of 4 tone pairsCertified to EN54 Part 25

GBP 328.32

1

Apollo XPander Red Beacon with Red Mounting Base - XPA-CB-14003-APO

Apollo XPander Red Beacon with Red Mounting Base - XPA-CB-14003-APOThe XPander Sounder Visual Indicator and Sounder Base is a wireless and designed to be used with XPander detectors and manual call points.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key Features WirelessBi-directional monitored radio platformChoice of 32 selectable tonesAudible self-test availableOutput is between 92dBA and 106dBA at 1m-dependent on tone setting

GBP 315.36

1

Apollo XPander Optical Smoke Detector and Mounting Base XPA-CB-12034-APO

Apollo XPander Optical Smoke Detector and Mounting Base XPA-CB-12034-APOThe XPander Optical Smoke Detector works on the light scatter principle and is ideal for applications where slow-burning or smouldering fires are likely.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key Features WirelessPerforms well in black and white smokeBi-directional radio communicationsXPERT card addressing systemFiveyear battery life using standard AA alkaline batteries

GBP 185.70

1

Apollo Marine Mini Switch Monitor 55000-775MAR

Apollo Marine Mini Switch Monitor 55000-775MARThe Marine Mini Switch Monitor is a miniature interface with an entirely new housing. The unit is designed to fit into equipment with limited space or mounted within an enclosure such as a manual call point. The interface can also be fitted onto a standard 35mm DIN-Rail using a twist-click motion. The unit is designed to monitor the state of one or more single pole volt-free contacts and reports the contact status to Apollo compatible control panels.OperationThe Marine mini switch monitor features a 20i shortcircuit isolator as standard and can be used as an interrupt or non-interrupt device. The interrupt feature selected via. the DIL Switch means the unit can be used where a priority response is required in particular for monitoring an individual or a zone of conventional manual call points.Please note When the eighth section of the DIL switch is changed the mini switch monitor will change the type code it sends to the panel. The panel will have to be programmed to accept this change.Key FeaturesDesigned for use where space is limitedIsolated as standardInterruptnon interrupt in one unitPre-alarm status availableThree coloured LEDs giving clear status indication

GBP 61.01

1

Apollo Discovery Marine Sounder Visual Indicator Base - 45681-394MAR

Apollo Discovery Marine Sounder Visual Indicator Base - 45681-394MARThe Discovery Marine sounder visual indicator base offers a choice of 15 evacuation tones including the standard Apollo evacuation tone. One of these tones is selected during commissioning in order to suit local regulations or customs.The tones include those required by Dutch Swedish German Australian New Zealand and North American standards as well as the UK. Whichever evacuation tone is selected there is a secondary tone which may be used for alerting or warning of a possible evacuation.ApplicationThe Discovery Marine sounder visual indicator base is used to provide audible and visual warning of fire and is controlled by the fire control panel by means of the Discovery protocol. The particular features of this base are available only when it is being controlled by the full Discovery protocol with the panel programmed accordingly.Information on features should be requested from the panel manufacturer. The Discovery Marine sounder visual indicator base can be used with a detector fitted or with a cap for operation as a stand-alone alarm device.Key FeaturesIt is possible to set individual control of the sounder and visual indicatorVolume and tone settings can be selected from the control panelElectronic bell toneIMO 1A tone included

GBP 103.58

1

Apollo XPander Single Input Output Channel Unit - XPA-IN-14011-APO

Apollo XPander Single Input Output Channel Unit - XPA-IN-14011-APOThe XPander InputOutput Unit is a radio based interface and offers two monitored input circuits and two relay outputs. It can be used for controlling fire doors fire dampers smoke vents and other fire engineering applications.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key Features WirelessMonitored switch circuitVoltage-free contactsCapable of switching up to 30V at 1AFiveyear battery life using standard AA alkaline batteries

GBP 198.37

1

Apollo XPander Dual Input Output Channel Unit - XPA-IN-14012-APO

Apollo XPander Dual Input Output Channel Unit - XPA-IN-14012-APOThe XPander InputOutput Unit is a radio based interface and offers two monitored input circuits and two relay outputs. It can be used for controlling fire doors fire dampers smoke vents and other fire engineering applications.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesWirelessMonitored switch circuitVoltage-free contacts Capable of switching up to 30V at 1AFive-year battery life using standard AA alkaline batteries

GBP 237.64

1

Apollo XPander Amber Beacon with White Mounting Base - XPA-CB-14004-APO

Apollo XPander Amber Beacon with White Mounting Base - XPA-CB-14004-APOThe XPander Sounder and Sounder Base is wireless and designed to be used with XPander detectors and manual call points.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key Featuresmodern stylingloop-powered interface operating on 868MHzwireless addresses seen by control panel as normal addressesradio base with wireless circuitry and battery compartmentchamber designed to inhibit dirt penetration and thus reduce false alarmsautomatic drift compensation with DirtAlert warningalgorithms for transient alarm rejectionFasTest reduces time taken to test detectorsremote test facility3-5 years battery life

GBP 321.25

1

Vores kunder ligger øverst på Google

Google Ads Specialister fra Vestjylland

Brand

Merchant

Price (EUR)