pure power tilbud from GBP 500 | See the cheapest prices and offers on css.nordicadpartner.dk

Baldwin Boxall VIGIL2 Power Supply with Dual Outputs BVSMP

Baldwin Boxall VIGIL2 Power Supply with Dual Outputs BVSMPVIGIL2 voice alarm system power supplies employ switch mode techniques to improve efficiency and reduce unwanted heat dissipation and weight.Key FeaturesThe BVSMP has two individually protected outputs at 24V the BVSMPLT has one.Each BVSMP will drive either two BV225 two BV125D or two BV050Q.Each BVSMPLT will drive one BV225 one BV125D or one BV050Q.Provide independent power converters with current and overvoltage protection circuits.Continual monitoring of the charger and all DC outputs ensures reliability.Standby batteries are continually float charged by the unit. Ensuring that in the event of mains failure power is maintained.Built-in deep battery discharge cut off preventing total discharge that can destroy the standby batteries in the event of AC power failure for long periods.A protected output is provided to power a mixer or auxiliary circuits.In the event of a fault condition an internal relay releases providing a changeover contact. A fault will be indicated on the EVAS router.The constant voltage charger is set for the recommended float charge. Should the battery fall below this level the BVSMP will charge at a constant rate of three Amps progressively reducing once the battery has achieved its nominal float level.Outputs together with a volt-free fault changeover contact are provided by a nine-way crimp connector plug and socket.Several chargers may be paralleled when used for larger systems. Paralleled BVSMPs must be synchronised.

GBP 1243.78

1

Baldwin Boxall VIGIL2 Dual 125W Class D Amplifier BV125D

Baldwin Boxall VIGIL2 Dual 125W Class D Amplifier BV125DThe BV125D Amplifier module contains two independent Class D Power amplifiers each with a single 500mV Balanced Line audio input and 125-Watt 100V Line output. The front panel status indicators show Power Overload and Output Level 10 and 100 output level for both amplifiers.The audio inputs to each amplifier are presented on separate RJ45 connectors. The outputs are presented on two 3-way plugcage clamp termination connectors providing 50V or 100V output. The 24V DC inputs are presented on two 2-way crimp connected sockets. The power output stages of the amplifiers are protected against overload conditions i.e. short circuits or abnormal loads.Should an amplifier be subjected to an abnormal load the input to the relevant power amplifier is attenuated to a safe level and the Overload LED will be illuminated. The amplifier output voltages are also sensed and should they exceed 100V the relevant input signal will be attenuated ensuring safe operation without creating unnecessary distortion.

GBP 1349.92

1

Baldwin Boxall BV3MDP10F Vigil 3 10 Way Mains Distribution with Fans

Baldwin Boxall BV3MDP10F Vigil 3 10 Way Mains Distribution with FansThe BV3MDP10F mains distribution panel with exhaust fans ensure that voice alarm racks are kept at the optimum operating temperature at all times working alongside the BV3MDPEFM. It features ten individual 6A fused amplifier IEC power outlet connections.Key Features10 6A fused amplifier IEC power outlet connectionsWorks alongside the BV3MDPEFMNo licence feesNo Ethernet switches requiredFast and responsive large systemSupports up to 254 voice alarm messagesFault tolerantAll connections monitored for reliability

GBP 1319.06

1

Baldwin Boxall BV3MDP05F Vigil 3 5 Way Mains Distribution with Fans

Baldwin Boxall BV3MDP05F Vigil 3 5 Way Mains Distribution with FansThe BV3MDP05F mains distribution panel with exhaust fans ensure that voice alarm racks are kept at the optimum operating temperature at all times working alongside the BV3MDPEFM. It features five individual 6A fused amplifier IEC power outlet connections.Key Features5 6A fused amplifier IEC power outlet connectionsWorks alongside the BV3MDPEFMColour BlackMaterial SteelNo licence feesNo Ethernet switches requiredFast and responsive large systemSupports up to 254 voice alarm messagesFault tolerantAll connections monitored for reliability

GBP 1267.36

1

Baldwin Boxall VIGIL2 Quad 50W Class D Amplifier BV050Q

Baldwin Boxall VIGIL2 Quad 50W Class D Amplifier BV050QThe Vigil2 BV050Q contains four independent 50 Watt Class D Power amplifiers each with one 500 mV balanced input and a 50 Watt 100V Line output. The front panel status indicators show Supply Healthy Overload Over Temperature and Output Level 10 and 100 max output level for each amplifier. The Active Indicator illuminates when the amplifier is not in Sleep Mode. CLASS D amplifiers are 80 efficient therefore reducing unwanted heat dissipation and power input requirements. Rated output power is obtainable using a 22V battery supply.The BV050Q has a Sleep mode automatically reducing the standby current requirement to typically 50mA per amplifier when operating on batteries. Channel gain may be individually set using the potentiometers on the board behind the front panel. The audio inputs to the amplifiers are presented on separate RJ45 connectors each connector providing the balanced audio input and a ground connection. The outputs are presented on 6-way plugscrew termination connectors providing 50V or 100V output. The 24V DC input is presented on a 2-way crimp connected plug and socket. The power output stage of the amplifier is protected against overload conditions i.e. short circuits or abnormal loads etc. Should the amplifier be subjected to an abnormal load the input to the power amplifier is attenuated to a safe level.The amplifiers output voltage is also sensed and should it exceed 100V the input signal will be attenuated ensuring safe operation without creating unnecessary distortion. Over temperature protection is provided using a sensor attached to the output stage heat sink. Should the temperature exceed 90 Degrees Celsius the input signal to will be attenuated to a safe level and the Overtemp LED will be illuminated. If the system is under surveillance it will cause the surveillance detector to indicate a fault condition due to the gain reduction. Up to three BV050Q Amplifier modules may be mounted in one BVMF equipment frame or more normally two amplifier modules and one switched mode power supply charger module.

GBP 1973.16

1

Baldwin Boxall VIGIL2 225W Class D Amplifier BV225

Baldwin Boxall VIGIL2 225W Class D Amplifier BV225The BV225 Amplifier module is a 225-Watt Class D Power amplifier with a 500mV Balance Line audio input and 100V Line output. The front panel status indicators show Power Overload and Output Level 10 and 100 output level. The audio input is presented on two separate RJ45 connectors. The output is presented on two 3-way plugcage clamp termination connectors providing 50V or 100V output. The 24V DC input is presented on a two 2-way crimp connected socket.The power output stage of the amplifier is protected against overload conditions i.e. short circuits or abnormal loads. Should an amplifier be subjected to an abnormal load the input to the relevant power amplifier is attenuated to a safe level and the Overload LED will be illuminated. The amplifier output voltages are also sensed and should they exceed 100V the relevant input signal will be attenuated ensuring safe operation without creating unnecessary distortion.Over temperature protection is provided using sensors attached to the output stage heat sink. Should the temperature exceed 90 Degrees Celsius the input signal to the relevant amplifier will be attenuated to a safe level and the Overload LED will be illuminated. If the system is under surveillance it will cause the surveillance detector to indicate a fault condition due to the gain reduction.

GBP 870.91

1

Baldwin Boxall VIGIL3 Dual 75W Class D Amplifier BV075D

Baldwin Boxall VIGIL3 Dual 75W Class D Amplifier BV075DThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV075D Dual 75W transformerless class D amplifier. Contains two independent 75W each amplifier has a single balanced line audio input and 75W 100V line output. Can either be used as two independent amplifier modules or two amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 1532.26

1

Baldwin Boxall VIGIL3 Quad 75W Class D Amplifier BV075Q

Baldwin Boxall VIGIL3 Quad 75W Class D Amplifier BV075QThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV075Q Quad 75W transformerless class D amplifier. Contains four independent 75W each amplifier has a single balanced line audio input and 75W 100V line output. Can either be used as four independent amplifier modules or four amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 2509.32

1

Baldwin Boxall VIGIL3 Dual 300W Class D Amplifier BV300D

Baldwin Boxall VIGIL3 Dual 300W Class D Amplifier BV300DThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV300D Dual 300W transformerless class D amplifier. Contains two independent 300W each amplifier has a single balanced line audio input and 300W 100V line output. Can either be used as two independent amplifier modules or two amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 2413.15

1

Baldwin Boxall VIGIL3 Quad 150W Class D Amplifier BV150Q

Baldwin Boxall VIGIL3 Quad 150W Class D Amplifier BV150QThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV150Q Quad 150W transformerless class D amplifier. Contains four independent 150W each amplifier has a single balanced line audio input and 150W 100V line output. Can either be used as four independent amplifier modules or four amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 2944.78

1

Baldwin Boxall VIGIL3 Dual 150W Class D Amplifier BV150D

Baldwin Boxall VIGIL3 Dual 150W Class D Amplifier BV150DThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV150D Contains two independent 150W each amplifier has a single balanced line audio input and 150W 100V line output. Can either be used as two independent amplifier modules or two amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 1787.18

1

Baldwin Boxall BVOCTSHUB OmniCarePLUS Network Hub Req BY24 amp 2 x IF PH

Baldwin Boxall BVOCTSHUB OmniCarePLUS Network Hub Req BY24 2 x IF PHThe OmniCarePLUS is the largest EVC system currently available on the market. The Network Control Hub BVOCTSHUB enables a touchscreen GUI to be connected to the OmniCarePLUS EVC system via a digital network.Key FeaturesThe BVOCTSHUB is included with each BVRDTSPCM touchscreen GUI.The network control hub houses a digital signal processor DSP audio matrix to allow for communication to the digital network.The digital network is fully monitored and any faults recorded in a time and date stamped log.The control hub includes batteries housed within the enclosure to provide system power in the event of a mains power failure - 24 hours quiescent and three hours at full operation.Wall mounting unit.Monitoring of all remote devices on the addressable loops.Monitors the status for all internal connections and interfaces including charger battery and remote signalling functions.Each power output is protected by a re-settable fuse rated at 2.5A.Connect multiple control hubs to a network each with a touchscreen GUI to provide site-wide control locations - with the ability to easily switch control.

GBP 5628.26

1

Baldwin Boxall Omnicare Emergency Tel Green Push Door CW Beacon BVOCETB

Baldwin Boxall Omnicare Emergency Tel Green Push Door CW Beacon BVOCETBThe Omnicare system offers a choice of outstation units which can be wired on the same loop from the control panel.The BVOCET emergencysteward telephone unit is one of the options available on this versatile system.Key FeaturesProvides two-way full duplex speech communication.Self-powered from ring circuit no local power source is required. Automatic battery backup is provided by the control panel in the event of a mains power failure.Green finish.With additional beacon BVOCETB.Push catch door slot lock version available BVOCETL.Addressable unit.The enclosure contains a rugged red handset with hearing aid compatible earpiece and loudspeaker.Calls are initiated upon opening the door. When answered the user can talk to the operator either by lifting the handset or hands-free. Closing the door ends the call.Conference call facility between multiple steward telephones is available via the operator at the control panel.All outstations are in a loop circuit from control panels.Surface mountable or flush mount with optional bezel.

GBP 622.34

1

Baldwin Boxall Omnicare Emergency Tel Green Lock Door CW Beacon BVOCETLB

Baldwin Boxall Omnicare Emergency Tel Green Lock Door CW Beacon BVOCETLBThe Omnicare system offers a choice of outstation units which can be wired on the same loop from the control panel.The BVOCET emergencysteward telephone unit is one of the options available on this versatile system.Key FeaturesProvides two-way full duplex speech communication.Self-powered from ring circuit no local power source is required. Automatic battery backup is provided by the control panel in the event of a mains power failure.Green finish.With additional beacon BVOCETB.Push catch door slot lock version available BVOCETL.Addressable unit.The enclosure contains a rugged red handset with hearing aid compatible earpiece and loudspeaker.Calls are initiated upon opening the door. When answered the user can talk to the operator either by lifting the handset or hands-free. Closing the door ends the call.Conference call facility between multiple steward telephones is available via the operator at the control panel.All outstations are in a loop circuit from control panels.Surface mountable or flush mount with optional bezel.

GBP 711.24

1

Baldwin Boxall BVOCECP OmniCare Remote - Red

Baldwin Boxall BVOCECP OmniCare Remote - RedThe OmniCare system offers a choice of outstation units which can be wired on the same loop from the control panel. The BVOCECPG standard green disabled refuge remote unit is one of the options available on this versatile system.Key FeaturesProvides two-way hands free speech steered communication.Self-powered from ring circuit no local power source is required. Automatic battery backup is provided by the control panel in the event of a mains power failure.Red finish also available in stainless steel BVOCECPG.Addressable unit.Volt free contact active when occupied. To operate overdoor lamps silence speakersounder etc.Stainless steel press to call button.Option to be permanently active if required.Reset from either remote unit using the key switch or via the master control panel.All outstations are in a loop circuit from control panels.A link to the fire detection system prevents hoax disabled refuge calls. This feature can be completely or partly overridden.Surface mounting unit can be flush mounted using a bezel.

GBP 567.91

1

Baldwin Boxall Omnicare Fire Tel Red Push Door CW Beacon BVOCFB

Baldwin Boxall Omnicare Fire Tel Red Push Door CW Beacon BVOCFBThe Omnicare system offers a choice of outstation units which can be wired on the same loop from the control panel. The BVOCF red fire telephone unit is one of the options available on this versatile system.Key FeaturesProvides two-way full duplex speech communication.Self-powered from ring circuit no local power source is required. Automatic battery backup is provided by the control panel in the event of a mains power failure.Red finish also available in stainless steel BVOCFS.With additional beacon BVOCFB.Push catch door slot lock version available BVOCFL.Addressable unit.The enclosure contains a rugged red handset with hearing aid compatible earpiece and loudspeaker.Calls are initiated upon opening the door. When answered the user can talk to the operator either by lifting the handset or hands-free. Closing the door ends the call.Conference call facility between multiple fire telephones is available via the operator at the control panel.All outstations are in a loop circuit from control panels.Surface mountable or flush mount with optional bezel.

GBP 604.20

1

Baldwin Boxall VIGIL3 Battery Charger Module BVMBC

Baldwin Boxall VIGIL3 Battery Charger Module BVMBCVIGIL3 is our next generation of voice alarm system products. The charger module fits alongside the VIGIL3 amplifiers in a 2U mainframe. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.Key FeaturesThe VIGIL3 battery charger module BVMBC is compact it is actually half the size of the VIGIL2 power supply charger unit.The module continually monitors the system backup batteries and charges them whenever this is necessary.Neatly fits alongside the VIGIL3 amplifiers in a 2U mainframe.Only one charger module is required for up to five VIGIL3 amplifier modules.Continually monitors the power supplies in five VIGIL3 amplifier modules.The module features an auxiliary DC output which can be used for powering other equipment.For use with the new more powerful lighter weight VIGIL3 amplifiers Dual 75 Watt BVO75D Quad 75 Watt BVO75Q Dual 150 Watt BV150D Quad 150 Watt BV150Q Dual 300 Watt BV300D.The BVMBC when used with VIGIL3 amplifiers and the EVAS BVRD2M4 routers forms a complete EN54 compliant voice alarm system.

GBP 501.68

1

Baldwin Boxall Omnicare Type B Advance Green Disable Refuge Remote BVOCA2G

Baldwin Boxall Omnicare Type B Advance Green Disable Refuge Remote BVOCA2GThe OmniCare system offers a choice of outstation units which can be wired on the same loop from the control panel. The BVOCA2G Advance green disabled refuge remote unit is one of the options available on this versatile system.Key FeaturesProvides two-way hands free speech steered communication.Self-powered from ring circuit no local power source is required. Automatic battery backup is provided by the control panel in the event of a mains power failure.Green finish also available in stainless steel BVOCA2S.Addressable unit.Induction loop Braille tactile and luminescent text. The front panel is also framed by a luminescent border.Volt free contact which is active when occupied to operate over-door lamps silence speakersounder etc.Large easy to use call button with an integral illuminated ring which ensures visibility at all times.Calls can be reset either by an extended press of the button on the remote unit or at the master control panel.All outstations are in a loop circuit from control panels.A link to the fire detection system prevents hoax disabled refuge calls. This feature can be completely or partly overridden.Surface mounting unit can be flush mounted using a bezel.

GBP 616.90

1

Baldwin Boxall Omnicare Type B Stainless Steel Disabled Refuge Remote BVOCECPS

Baldwin Boxall Omnicare Type B Stainless Steel Disabled Refuge Remote BVOCECPSThe OmniCare system offers a choice of outstation units which can be wired on the same loop from the control panel. The BVOCECPS standard green disabled refuge remote unit is one of the options available on this versatile system.Key FeaturesProvides two-way hands free speech steered communication.Self-powered from ring circuit no local power source is required. Automatic battery backup is provided by the control panel in the event of a mains power failure.Stainless steel finish also available in green BVOCECPG.Addressable unit.Volt free contact active when occupied. To operate over-door lamps silence speakersounder etc.Stainless steel press to call button.Calls can be reset either by of the key-switch on the remote unit or at the master control panel.Option to be permanently active if required.Reset from either remote unit using the key switch or via the master control panel.All outstations are in a loop circuit from control panels.A link to the fire detection system prevents hoax disabled refuge calls. This feature can be completely or partly overridden.Surface mounting unit can be flush mounted using a bezel.Please note Stainless steel products are not intended for installation in humid areas.

GBP 499.87

1

Baldwin Boxall C2CSTDCS CARE2 Non-Networked System Critical Spares Kit

Baldwin Boxall C2CSTDCS CARE2 Non-Networked System CriticalSpares KitThe C2CSTDCS manufactured by Baldwin Boxall is a criticalspares kit for care2 non-networked system. This kit typically includesessential components needed for maintenance or repairs ensuring thatfacilities can keep their communication systems operational. Kit IncludesBA021T Fuse 2A Slow 20mmC2CEK4 Care2 Console Expansion Kit 4 WayC2CFPE Care2 Console Fire PanelEthernet ModuleC2RTH Care2 Roam Fire Tel Handset RedKEYBVE Single Spare Key for Refuge ConsoleKEYBVR Pair of Spare Keys for Refuge RemoteQ1352_5.9 Care2 Console Front Panel PCBA SR70W 70W Power SupplyCharger

GBP 1021.51

1

Baldwin Boxall C2CNWCS CARE2 Networked System Critical Spares

Baldwin Boxall C2CNWCS CARE2 Networked System CriticalSparesThe C2CNWCS manufactured by Baldwin Boxall is a criticalspares kit for care2 networked system. This kit typically includes essentialcomponents needed for maintenance or repairs ensuring that facilities can keeptheir communication systems operational.Kit IncludesBA021T Fuse 2A Slow 20mmC2CEK4 Care2 Console Expansion Kit 4 WayC2CFPE Care2 Console Fire PanelEthernet ModuleC2CN Care2 Console Network Module CW FP InterfaceC2RTH Care2 Roam Fire Tel Handset RedKEYBVE Single Spare Key for Refuge ConsoleKEYBVR Pair of Spare Keys for Refuge RemoteQ1352_5.9 Care2 Console Front Panel PCBASR70W 70W Power SupplyCharger

GBP 1514.11

1

Baldwin Boxall Omnicare Type B Advance Stainless Steel Disabled Refuge Remote BVOCA2S

Baldwin Boxall Omnicare Type B Advance Stainless Steel Disabled Refuge Remote BVOCA2SThe OmniCare system offers a choice of outstations which can be wired on the same loop from the control panel. The BVOCA2S Advance stainless-steel disabled refuge unit is one of the options available on this versatile system.Key FeaturesProvides two-way hands free speech steered communication.Self-powered from ring circuit no local power source is required. Automatic battery backup is provided by the control panel in the event of a mains power failure.Stainless steel finish also available in green BVOCA2G.Addressable unit.Induction loop Braille tactile and luminescent text. The front panel is also framed by a luminescent border.Volt free contact which is active when occupied to operate over-door lamps silence speakersounder etc.Large easy to use call button with an integral illuminated ring which ensures visibility at all times.Calls can be reset either by an extended press of the button on the remote unit or at the master control panel.All outstations are in a loop circuit from control panels.A link to the fire detection system prevents hoax disabled refuge calls. This feature can be completely or partly overridden.Surface mounting unit can be flush mounted using a bezel.Please note Stainless steel products are not intended for installation in humid areas.

GBP 821.93

1

Baldwin Boxall Omnicare Type A Red Fire Telephone with Push Door BVOCF

Baldwin Boxall Omnicare Type A Red Fire Telephone with Push Door BVOCFThe OmniCare system offers a choice of outstation units which can be wired on the same loop from the control panel. The BVOCF red fire telephone unit is one of the options available on this versatile system.Fire telephones are used by fire officers and those responsible for the evacuation of a building during an emergency. They provide essential communication for those in control. When operated by opening the door of the enclosure the persons managing the evacuation at the control panel can immediately see the location of the caller as this is indicated on the panel. The fire officer at the telephone point can relay the situation and confirm if that area is clear of personnelpublic before moving to the next levelarea.The fire telephone is connected to the control panel in a loop circuit and can be included with disabled refuge outstations on the same panel.Key FeaturesProvides two-way full duplex speech communication.Self-powered from ring circuit no local power source is required. Automatic battery backup is provided by the control panel in the event of a mains power failure.Red finish also available in stainless steel BVOCFS.Push catch door slot lock version available BVOCFL.Addressable unit.The enclosure contains a rugged red handset with hearing aid compatible earpiece and loudspeaker.Calls are initiated upon opening the door. When answered the user can talk to the operator either by lifting the handset or hands-free. Closing the door ends the call.Conference call facility between multiple fire telephones is available via the operator at the control panel.All outstations are in a loop circuit from control panels.Surface mountable or flush mount with optional bezel.

GBP 540.70

1

Baldwin Boxall Omnicare Combined Disabled Refuge Unit with Lock Door BVOCCL

Baldwin Boxall Omnicare Combined Disabled Refuge Unit with Lock Door BVOCCLThe combined unit for the Omnicare LOOP-wired EVC system provides two types of call point at one location. This unit was the first of its kind on the market and has been installed in many locations worldwide.The Omnicare combined outstation has been specially designed so that it can be installed in such a way as to enable correct mounting heights for each section of the unit as laid out in BS5839-9. The combined unit can be placed on the wiring loop in combination with any other Omnicare style outstation providing users great flexibility and choice.Key FeaturesSelf-powered from ring circuit no local power source is required. Automatic battery backup is provided by the control panel in the event of a mains power failure.Red finish also available in stainless steel BVOCCS.Slot lock door.Addressable unit.Surface mount or flush mount with optional bezel.All outstations are in a loop circuit from control panels.Fire telephone Features Provides two-way full duplex speech communication.The fire telephone section contains a rugged red handset with hearing aid compatible earpiece and loudspeaker.Calls are initiated upon opening the door. When answered the user can talk to the operator either by lifting the handset or hands-free. Closing the door ends the call.Conference call facility between multiple fire telephones is available via the operator at the control panel.Disabled refuge remote Provides two-way hands free speech steered communication.Volt free contact active when occupied. To operate over-door lamps silence speakersounder etc.Stainless steel press to call button.Calls can be reset either by of the key-switch on the remote unit or at the master control panel.Option to be permanently active if required.Reset from either remote unit using the key switch or via the master control panel.

GBP 886.33

1

Baldwin Boxall Omnicare Combined Stainless Steel Disabled Refuge Unit with Lock Door BVOCCSL

Baldwin Boxall Omnicare Combined Stainless Steel Disabled Refuge Unit with Lock Door BVOCCSLThe combined unit for the Omnicare Loop-wired EVC system provides two types of call point at one location. This unit was the first of its kind on the market and has been installed in many locations worldwide.The Omnicare combined outstation has been specially designed so that it can be installed in such a way as to enable correct mounting heights for each section of the unit as laid out in BS5839-9. The combined unit can be placed on the wiring loop in combination with any other Omnicare style outstation providing users great flexibility and choice.Key FeaturesSelf-powered from ring circuit no local power source is required. Automatic battery backup is provided by the control panel in the event of a mains power failure.Stainless steel finish also available in red BVOCC.Slot lock door.Addressable unit.Surface mount or flush mount with optional bezel.All outstations are in a loop circuit from control panels.Fire telephone Provides two-way full duplex speech communication.The fire telephone section contains a rugged red handset with hearing aid compatible earpiece and loudspeaker.Calls are initiated upon opening the door. When answered the user can talk to the operator either by lifting the handset or hands-free. Closing the door ends the call.Conference call facility between multiple fire telephones is available via the operator at the control panel.Disabled refuge remote Provides two-way hands free speech steered communication.Volt free contact active when occupied. To operate over-door lamps silence speakersounder etc.Stainless steel press to call button.Calls can be reset either by of the key-switch on the remote unit or at the master control panel.Option to be permanently active if required.Reset from either remote unit using the key switch or via the master control panel.Please note Stainless steel products are not intended for installation in humid areas.

GBP 1071.41

1

Vores kunder ligger øverst på Google

Google Ads Specialister fra Vestjylland

Brand

Merchant

Price (EUR)