giro imperial from GBP 0 | See the cheapest prices and offers on css.nordicadpartner.dk

20-L-100F Imperial Pilot Bore Timing Pulley, 20 Teeth, 3/8" Pitch, for A 1" Wide Belt

Imperial timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 0.00

1

19-L-100F Imperial Pilot Bore Timing Pulley, 19 Teeth, 3/8" Pitch, for A 1" Wide Belt

Imperial timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 0.00

1

1008-3/4 Imperial Taper Bush

Taper Bushes are a convenient and cost effective method of fixing components to a mating shaft without using any special tools. Taper Bushes are pre-machined with the required bore & keyway size and are supplied complete with locking set screws. Taper Bushes are designed for use with V-Pulleys, Chain Sprockets, Micro V-Pulleys, Timing Belt Pulleys, Couplings, and Weld-On & Bolt-On Hubs. Part numbers are identified by a 4 digit number (e.g. 1610) which represents the taper bush series followed by the bore size (e.g. 1/2mm) for example 1610/1/2

GBP 0.00

1

70XL037 Rubber Chain Timing Belt

XL Dunlop imperial timing belts are manufactured using the most advanced technology available. Trapezoidal tooth profile and Polychloroprene teeth offer accurate meshing with the mating pulleys and this contributes to the ability to absorb shock loads and reduced interference. Fibreglass reinforcement for minimal elongation and a nylon fabric protects the tooth surface.

GBP 0.00

1

352XL037 Rubber Chain Timing Belt

XL Dunlop imperial timing belts are manufactured using the most advanced technology available. Trapezoidal tooth profile and Polychloroprene teeth offer accurate meshing with the mating pulleys and this contributes to the ability to absorb shock loads and reduced interference. Fibreglass reinforcement for minimal elongation and a nylon fabric protects the tooth surface.

GBP 0.00

1

316XL037 Rubber Chain Timing Belt

XL Dunlop imperial timing belts are manufactured using the most advanced technology available. Trapezoidal tooth profile and Polychloroprene teeth offer accurate meshing with the mating pulleys and this contributes to the ability to absorb shock loads and reduced interference. Fibreglass reinforcement for minimal elongation and a nylon fabric protects the tooth surface.

GBP 0.00

1

202L075 Rubber Chain Timing Belt

Dunlop imperial timing belts are manufactured using the most advanced technology available. Trapezoidal tooth profile and Polychloroprene teeth offer accurate meshing with the mating pulleys and this contributes to the ability to absorb shock loads and reduced interference. Fibreglass reinforcement for minimal elongation and a nylon fabric protects the tooth surface. XL L & H Images are for illustration purposes only.

GBP 0.00

1

0-L-075F Imperial Pilot Bore Timing Pulley, 20 Teeth, 3/8" Pitch, for A 3/4" Wide Belt

Dunlop timing belt pulleys are manufactured from either C45 steel with black oxide surface treatment, cast iron EN-GJL-200 and black phosphate or aluminium 6082. Pulley flanges are produced from S235JR steel. Timing belt pulleys are available to suit all pitch sizes.

GBP 0.00

1

21-L-075F Imperial Pilot Bore Timing Pulley, 21 Teeth, 3/8" Pitch, for A 3/4" Wide Belt

Dunlop timing belt pulleys are manufactured from either C45 steel with black oxide surface treatment, cast iron EN-GJL-200 and black phosphate or aluminium 6082. Pulley flanges are produced from S235JR steel. Timing belt pulleys are available to suit all pitch sizes.

GBP 0.00

1

31-28 06B (3/8" X 7/32") Simplex Sprockets - - Taper Bore - 3/8" Pitch

Taper bore sprockets are manufactured to internationally recognised standards DIN8187-ISO/R 606 and are produced from C45 steel UNI EN 10083-1 having a minimum strength of 600 N/mm 2 and GG22 EN-GJL-200 UNI 1561 cast iron. They have a black phosphated finish to increase corrosion resistance so extending the sprockets working life. Convenient taper bore to suit a standard taper bush that are pre-bored to suit both metric & imperial bore and key way sizes. Available to suit British standard roller chains 06B-1 (Simplex) 3/8" pitch sizes.

GBP 0.00

1

Vores kunder ligger øverst på Google

Google Ads Specialister fra Vestjylland

Brand

Size

Merchant

Price (EUR)

20-L-100F Imperial Pilot Bore Timing Pulley, 20 Teeth, 3/8" Pitch, for A 1" Wide Belt

19-L-100F Imperial Pilot Bore Timing Pulley, 19 Teeth, 3/8" Pitch, for A 1" Wide Belt

1008-3/4 Imperial Taper Bush

70XL037 Rubber Chain Timing Belt

352XL037 Rubber Chain Timing Belt

316XL037 Rubber Chain Timing Belt

202L075 Rubber Chain Timing Belt

0-L-075F Imperial Pilot Bore Timing Pulley, 20 Teeth, 3/8" Pitch, for A 3/4" Wide Belt

21-L-075F Imperial Pilot Bore Timing Pulley, 21 Teeth, 3/8" Pitch, for A 3/4" Wide Belt

31-28 06B (3/8" X 7/32") Simplex Sprockets - - Taper Bore - 3/8" Pitch

NORDIC AD PARTNER

Powered by Cobiro