kaffemaskine 1 kop from GBP 1 | See the cheapest prices and offers on css.nordicadpartner.dk

Hochiki SMB-1 Enclosure Grey Base Clear Lid

Hochiki SMB-1 Enclosure Grey Base Clear LidModel SMB-1 is from a range of IP66 rated grey RAL7035 enclosures designed for use with the Hochiki range of CHQ Modules. The SMB-1 features a selection of metric knock-outs and is supplied with a transparent black lid as standard.Used in conjunction with the SMB-ADAPTOR an adaptor plate sold separately this enclosure can house any of the PCB assemblies from the Hochiki Smart-Fix Module range or the CHQ-SIM CHQ-POM or CHQ-SOM mini modules.Key FeaturesQuick-release screwsPolyurethane gasket provides IP66 protectionCorrosion free resistant to most alkaline and acidTemperature resistance to 70 deg C Impact resistant and Non-flammable32 knock-outs

GBP 31.72

1

Hochiki SCPCALLPOINTKEY Reset STI Call Point Keys With Pips - 1 Piece

Hochiki SCPCALLPOINTKEY Reset STI Call Point Keys With Pips - 1 Piece1 x call point key for the STI Reset Call Point range.Comes with pips

GBP 1.13

1

Hochiki LEAKalarm Addressable Water Leak Detection Control Panel 1 loop LAAP-S-1

Hochiki LEAKalarm Addressable Water Leak Detection Control Panel 1 loop LAAP-S-1Single and dual loop LEAKalarm control panels are available with each loop supporting a maximum of 127 addressable devices.Loop supported ancillaries include a mains relay controller which is ideal for solenoid valve activation and plant equipment control an addressable remoteindicator and short circuit isolator. LEAKalarm loop modules can be configured to operate in accordance with powerful cause and effect delivered via our LoopExplorer 2 software.LEAKalarm Control Panels are equipped with both common Alarm and Fault relays as well as battery backup.Key FeaturesBoth single and dual loop control panels availableA single loop panel can support up to 254 LEAKalarm Probes or over 12000m of water leak detection cableA dual loop panel can support in excess of 500 LEAKalarm Probes and over 25000m of water leak detection cableControl panel configuration allows each addressable device to be uniquely identifiedRemote outputs fully configurableRS485 panel expansion bus supporting up to 32 additional accessoriesCause and Effect output control via Loop Explorer 2 PC softwareFully monitored sounder circuitsAdditional 8-Way relay board also availableBattery Standby

GBP 1003.45

1

Hochiki 1 Pipe Aspiration Smoke Detector with Docking Station FIRELINK-25

Hochiki FIRELINK-25 1 Pipe Aspiration Smoke Detector with Docking StationFIRElink-25 is designed to provide very high sensitivity smoke detection in a small package. A unique sensing technology ensures that the detector operates at optimum sensitivity for the protected environment without the need for complex setup. This means the product will configure itself to provide high sensitivity in a computer room or reduced sensitivity in a smoky area.The detector is designed to fit into a Docking Station which accepts all sampling pipes and cables leaving the detector to be fitted during the final commissioning phase. This ensures that the detector is less likely to be damaged during installation. Volt-free Fire 1 and Fault relay outputs are provided for remote monitoring by local fire detection or BMS systems.Key FeaturesUltra-small low cost aspirating smoke detector for easy and discreet installationHigh sensitivity provided by laser based forward light scatter for reliable early warningSingle sampling pipe up to 50 m in length still airFalse alarms reduced by unique laser sensing technology - able to discriminate against dustRS485 communications built in as standard for networking and remote communications

GBP 1485.29

1

Hochiki LEAKalarm Single Loop Expansion Card LAAP-LEC

Hochiki LEAKalarm Single Loop Expansion Card LAAP-LECA loop expansion card designed for the LEAKalarm Water Leak Detection Control Panel. Can be used in conjunction with the 1 loop control panel LAA-S-1 to convert it to a 2 loop.Key FeaturesEasy to install plugs into existing motherboardRequires Loop Explorer 2 software account

GBP 465.90

1

Hochiki FL-APIC FIRElink APIC Interface Card

Hochiki FL-APIC FIRElink APIC Interface CardSupports both single and multi mode operationFull address range 1-127Compatible with all FIRElink detectors and command modules

GBP 287.18

1

Hochiki SMB-1LID Lid for Enclosure Grey

Hochiki SMB-1LID Lid for Enclosure GreyAn alternative lid for the SMB-1 enclosure moulded in grey ABS - can replace the semi-transparent grey lid supplied as standard.Key FeaturesOpaque grey ABSAlternative to standard semi-transparent lid

GBP 12.76

1

Hochiki Conventional Call Point Key Switch 2 Position with Red Backbox CCP-KS

Hochiki CCP-KS Conventional Call Point Key Switch 2 Position with Red BackboxThe CCP-KS is a red Conventional key switch manual call-point based upon the industry standard KAC 9000 series housing and features flying leads for simple wiring. The unit features two key positions marked as 1 and 0 with the key easily removable in either position.Key FeaturesTwo position key switch marked 1 and 0Key removable in both positionsTerminals can accommodate up to a 2.5 mm solid conductorSupplied in RED - other colours available on requestSupplied with back box for surface fixingSuitable for fire security and other specialist applications

GBP 35.10

1

Hochiki SMB-ADAPTOR SMB Adaptor Plate

Hochiki SMB-ADAPTOR SMB Adaptor PlateThe SMB-ADAPTOR is a mounting plate designed to be fitted within the SMB-1 module enclosure to facilitate the mounting of the CHQ range of modules and mini modules.The CHQ range of modules is fitted utilising the CHQ-ADAPTOR an adaptor which allows the PCB assembly of the CHQ Module to be removed and mounted within enclosures. The mini modules such as the CHQ-POM can be fitted directly to the SMB-ADAPTOR plate.Key FeaturesProvides multiple fixing options for the CHQ module rangeEasy to install within the SMB-1 enclosurePre-drilled with correct fixing holes

GBP 31.75

1

Hochiki Infra-Red Flame Detector Alloy Housing - IR3 IFD-E

Owing to present delivery delays from the OEM of this product please see alternative equipment below for your consideration with regard to your on-going ProjectsSpectrex SharpEye 2020MI - Mini Triple IR IR3 Flame Detector 2020-MI-1-1-FTriple IR Flame Detector - FlameSpec-IR3 FLS-IR3-AS11Hochiki Infra-Red Flame Detector Alloy Housing - IR3 IFD-EModel IFD-E is an IR flame detector designed for use where open flaming fires may be expected and responds to the light emitted from flames during combustion.The detector discriminates between flames and other light sources by responding only to particular optical wavelengths and flame flicker frequencies. This enables the detector to avoid false alarms due to such factors as flickering sunlight Ideal for the detection of flames from the burning of Aviation Fuels kerosene Butane Grain Feeds Hydrogen Paper Natural Gas Petrol gasoline etc.Key FeaturesUnaffected by convection currents draughts or wind and solar-blindTolerant of fumes vapours dust and mistResponsive to a flame more than 25 m awaySelectable response speedClass 1 performance as defined in BS EN54-102002 on the high sensitivity settingOptical self-testSIL capable

GBP 3069.36

1

Hochiki Conventional 2 Wire Base YBO-R6PA Ivory

Hochiki Conventional 2 Wire Base YBO-R6PA IvoryModel YBO-R6PA is a Conventional Detector Mounting Base for 2-Wire S systems where detectors and sounders are on same zone cables.Key FeaturesIntegral remote indicator outputRugged designDedicated cable screen terminalQuick connection via square cable clampsAccepts from 1 to 2.5 mm cablesBayonet slot low insertion force for detectors

GBP 15.17

1

Hochiki Conventional White 2 Wire Base YBO-R6PAWHT

Hochiki Conventional White 2 Wire Base YBO-R6PAWHTModel YBO-R6PAWHT is a Conventional Detector Mounting Base for 2-Wire S systems where detectors and sounders are on same zone cables control panel compatibility required.Key FeaturesIntegral remote indicator outputRugged designDedicated cable screen terminalQuick connection via square cable clampsAccepts from 1 to 2.5 mm cablesBayonet slot low insertion force for detectors

GBP 15.17

1

Hochiki Conventional Wall Sounder Beacon - White case - non EN54-23 compliant CWSB-EWHT

Hochiki Conventional Wall Sounder Beacon - White case non EN54-23 compliantThe beacon and sounder are fully synchronised. The unit is supplied with its own base a shallow base IP21 or a deep base IP33. Other lens colours are available upon request.Key FeaturesRobust designLow current consumptionEasy to installMaximum 113 dBA 1 metre Tone 1532 user-selectable tonesUtilises high intensity LED technologyEN54 Part 3 approval

GBP 66.06

1

Hochiki Multi-Heat Sensor - Black case - ATJ-ENBLK

Hochiki Multi-Heat Sensor - Black case - ATJ-ENBLKThe ATJ-EN incorporates a variable temperature heat element and a rate of rise heat element both of which are controlled from the Control Panel allowing either thermal element or both elements simultaneously to be active in making the fire decision 1.The sensor polling LEDs can also be controlled via the Control Panel pulsingnon-pulsing 1Check control panel compatibility

GBP 47.08

1

Hochiki Conventional Wall Sounder Beacon - Red case non EN54-23 compliant CWSB-E

Hochiki Conventional Wall Sounder Beacon - Red case non EN54-23 compliant CWSB-EA Conventional Wall Sounder Beacon with improved electronic design enables very low current consumption whilst providing a range of tones and volumes selectable from each unit. Features integral beacon.Key FeaturesRobust DesignLow Current ConsumptionEasy to InstallMaximum 113 dB A 1 Meter Tone 1532 User Selectable Tones And 3 User VolumesUtilises High Intensity LEDs

GBP 66.06

1

Hochiki Single Output Module CHQ-SOM

Hochiki CHQ-SOM Single Output ModuleThe CHQ-SOM has been designed to allow a single relay output to be connected to the ESP loop. The unit incorporates a volt-free relay contact that can be configured as either NO or NC the relay contact is rated to 30 V dc max 1 A resistive load. The CHQ-SOM features three colour-coded flying leads the unit also features a wiring terminal block for loop connection.Key FeaturesIncludes a single monitored outputSmall design for simple provision of a monitored output onto an ESP loopFlying leads for easy installationAddressed with TCH-B100 Hand Held ProgrammerApproved by LPCBPlease Note To maintain LPCB approval the device must be mounted in an SMB-1 enclosure or an equivalent enclosure made from polycarbonate or a similar material which is impact resistant as per EN54-182005 Clause 5.9 in conjunction with the SMB-ADAPTOR plate using two M3 screws or two M3 nuts and bolts.

GBP 42.07

1

Hochiki Conventional Wall Sounder BANSHEE EXCEL

Hochiki Conventional Wall Sounder BANSHEE EXCELThe BANSHEE EXCEL is an electronic conventional sounder for internal use. It is easily installed with robust terminations that can accept 2.5 mm2 cables and a push and twist bayonet-fitting base.The units various industry-standard tones and volume levels are all user-selected using simple DIL switches on the underside.Key FeaturesRobust designLow current consumptionEasy to installMaximum 110dBA at 1 metre dependant on tone selected32 user-selectable tones

GBP 32.71

1

Hochiki Conventional Wall Sounder White BANSHEE-EXCEL-CH-WHITE

Hochiki Conventional Wall Sounder White BANSHEE-EXCEL-CH-WHITEThe BANSHEE EXCEL is an electronic conventional sounder for internal use.It is easily installed with robust terminations that can accept 2.5 mm2 cables and a push and twist bayonet-fitting base.The units various industry-standard tones and volume levels are all user-selected using simple DIL switches on the underside.Key FeaturesRobust designLow current consumptionEasy to installMaximum 110 dBA at 1 metre dependant on tone selected32 user-selectable tones

GBP 32.71

1

Hochiki LA-HSSB1 LEAKalarm Addressable Sounder Beacon White Case Blue Lens

Hochiki LA-HSSB1 LEAKalarm Addressable Sounder Beacon White Case Blue LensA sounder beacon compatible with the LEAKalarm water leak detection system. This multi-tone sounder and strobe is easily installed with robust terminations that can accept 2.5 mm cables and a push and twist bayonet-fitting base. The blue lens distinguishes the unit as non-fire.Key FeaturesRobust designLow current consumptionEasy to installXenon beacon technologyMaximum 110 dBA at 1 m dependent on tone selected32 user-selectable tones

GBP 84.47

1

Hochiki Conventional Intrinsically Safe Heat Detector DCD-1E-IS

Hochiki DCD-1E-IS Conventional Intrinsically Safe Heat DetectorThe DCD-1E-IS is an Intrinsically Safe Conventional Rate of Rise Heat Detector with a 60 fixed temperature element designed for use in hazardous areas. The unit also features a remote indicator output.Key FeaturesTwin fire LEDs allow 360 degree viewingElectronics free mounting baseRemote indicator outputATEX Classification to II 1G EEx ia IIC T5 Tamb55CSuitable for installation in areas at Category 1 inc all lower categoriesAlso available in whiteApproved by LPCB and GLSIL2 Approved variant available

GBP 62.75

1

Hochiki Conventional White Intrinsically Safe Heat Detector DCD-1E-ISWHT

Hochiki DCD-1E-ISWHT Conventional White Intrinsically Safe Heat DetectorThe DCD-1E-ISWHT is an Intrinsically Safe Conventional Rate of Rise Heat Detector with a 60 fixed temperature element designed for use in hazardous areas. The unit also features a remote indicator output.Key FeaturesTwin fire LEDs allow 360 degree viewingElectronics free mounting baseRemote indicator outputATEX Classification to II 1G EEx ia IIC T5 Tamb55CSuitable for installation in areas at Category 1 inc all lower categoriesAlso available in ivoryApproved by LPCB and GLSIL2 Approved variant available

GBP 62.75

1

Hochiki BANSHEEEXCELIP66 Conventional Weatherproof Wall Sounder

Hochiki BANSHEEEXCELIP66 Conventional Weatherproof Wall SounderThe BANSHEE EXCEL IP66 is an electronic conventional sounder for external use. It is easily installed with robust terminations that can accept 2.5 mm2 cables and a push and twist bayonet-fitting base. The units various industry-standard tones and volume levels are all user-selected using simple DIL switches on the underside. The deep weatherproof base affords an ingress protection rating of IP66.Key FeaturesRobust designLow current consumptionEasy to installMaximum 110 dBA at 1 metre dependant on tone selected32 user-selectable tonesWeatherproof baseIP Rating IP66

GBP 34.69

1

Hochiki Conventional Infrared Flame Detector DRD-E

Hochiki DRD-E Conventional Infrared Flame DetectorThe DRD-E is a flame detector designed for internal use to detect large flames. The detector fits any of the CDX range of mounting bases. The detection zone is a 90 cone and the detection range is up to and including 25 m.Key FeaturesClass 1 performance as defined in BS EN54-102002 range up to 25 mSingle IR technologyRobust and slim designLow current consumptionEasy to installFits any of the CDX Range of mounting basesTwin LEDs for 360 degree viewingApproved by LPCB VdS

GBP 371.70

1

Hochiki Ekho EK-WL8-EXP Wireless Expander Module

Hochiki Ekho EK-WL8-EXP Wireless Expander ModuleThe EK-WL8-EXP Expander Module increases radio coverage of an Ekho Translator Module allowing the use of the system in larger buildings and in difficult wireless environments. Multiple Expanders can be utilised in a micro cell structure to provide a solution to large complex systems.When multiple Expander Modules two or more are used these provide a MESH solution maintaining the wireless systems integrity. The system allows up to 126 Expander Modules or field devices to be configured to any one Translator Module 1.Any combination of Ekho wireless devices can be connected to the Expander Module 1. The Expander Module transmits the intelligent device information from the field devices to the Loop Translator Module using a highly stable bi-directional radio communication protocol. The system parameters are programmed into the Expander Module via the Translator Module.The Expander Module is fitted with two internal antennas reducing signal fading and ensuring reliable radio communications. An optional back box is also available.Key FeaturesApproved to EN54-18 and 25RED compliantSupports MESH communicationsBi-directional wireless communicationSelf-optimising wireless amplitude and frequencyMakes additions to existing wired systems easy and cost effectiveRequires external power supply 24 VDCOptional back box can be bought separately

GBP 318.46

1

Hochiki Conventional White Sounder Base CSB-EWHT

Hochiki CSB-EWHT Conventional White Sounder BaseThe CSB-EWHT is platform type sounder which will accept the CDX Range of detectors mounted with an appropriate base. The improved electronics result in a very low current consumption with a high sound output. A set of DIL switches are used to select the units tone and sound output three settings LOW MEDIUM and HIGH.Compatible CDX Bases - YBN-R6WHT YBO-R6PAWHT YBO-R6RWHT YBO-R6RNWHT YBO-R6RSWHT YBN-R6SKWHTKey FeaturesRobust designLow current consumptionEasy to installMaximum 93 dBA 1 metre Tone 132 user-selectable tones and 3 user-selectable volumesLockable cap availableEN54 Part 3 approval

GBP 30.32

1

Vores kunder ligger øverst på Google

Google Ads Specialister fra Vestjylland

Brand

Merchant

Price (EUR)