Vores kunder ligger øverst på Google

Google Ads Specialister fra Vestjylland

Vi er 100% dedikerede til Google Annoncering – Vi har mange års erfaring med Google Ads og den bruger vi på at opsætte, optimere & vedligeholde vores fantastiske kunders konti.

100% Specialiseret i Google Ads
Vi har mange års erfaring fra +300 konti
Ingen lange bindinger & evighedskontrakter
Jævnlig opfølgning med hver enkelt kunde
Vi tager din virksomhed seriøst
KONTAKT OS
LÆS UDTALELSER & SUCCESHISTORIER

284 results (0,14705 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Kentec Sigma XT Extinguishant Coincidence Unit 1 Area to EN12094-1 Surface

Kentec Sigma XT Extinguishant Coincidence Unit 1 Area to EN12094-1 Surface

Kentec Sigma XT Extinguishant Coincidence Unit 1 Area to EN12094-1 SurfaceThe Sigma XT ECU coincidence unit has two fully monitored inputs for connection to fire detection control equipment or addressable control modules to provide an EN12094-1 EN54-2 and EN54-4compliant extinguishant control system. Its many programmable features and extensive range of inputs and outputs make the Sigma XT ECU coincidence unit suitable for all extinguishing applications where a fully featured control device is required.Among the many features of the Sigma XT ECU are serially connected status units for reduced wiring and reduced installation cost dual extinguishant outputs that may be configured for mainreserve applications and a countdown timer which displays the time until discharge of the extinguishant in seconds. All units are independently configurable via a simple code based programming interface to suit the desired application.Key FeaturesApproved to EN12094-1 EN54-2 and EN54-4Dual extinguishant outputsFirst and second stage sounder outputsFirst and second stages relay contactsMain reserve facilitySerial connection to status unitsDischarge countdown time indicator

GBP 616.56
1

Kentec K1630313 Battery Box to Match Syncro Styling Max 38 AH Battery Surface

Kentec K1630313 Battery Box to Match Syncro Styling Max 38 AH Battery Surface

Kentec K1630313 Battery Box to Match Syncro Styling Max 38 AH Battery SurfaceK16000 series battery enclosures provide a convenient means of fitting extra batteries for increased standby capacity for fire protection and detection systems.Ranges are available to match Syncro styled or Sigma styled control equipment. All units are constructed with the same high-quality steel and with the same finish as the control equipment.A range of enclosure sizes is available allowing a broad range of battery sizes to be fitted.

GBP 252.30
1

Kentec K1620203 Battery Box to Match Syncro Styling Max 17 AH Battery Surface

Kentec K1620203 Battery Box to Match Syncro Styling Max 17 AH Battery Surface

Kentec K1620203 Battery Box to Match Syncro Styling Max 17 AH Battery Surface K16000 series battery enclosures provide a convenient means of fitting extra batteries for increased standby capacity for fire protection and detection systems.Ranges are available to match Syncro styled or Sigma styled control equipment. All units are constructed with the same high-quality steel and with the same finish as the control equipment.A range of enclosure sizes is available allowing a broad range of battery sizes to be fitted.

GBP 188.88
1

Kentec K1610245 Battery Box to Match Syncro Styling Max 65 AH Battery Surface

Kentec K1610245 Battery Box to Match Syncro Styling Max 65 AH Battery Surface

Kentec K1610245 Battery Box to Match Syncro Styling Max 65 AH Battery SurfaceK16000 series battery enclosures provide a convenient means of fitting extra batteries for increased standby capacity for fire protection and detection systems.Ranges are available to match Syncro styled or Sigma styled control equipment. All units are constructed with the same high-quality steel and with the same finish as the control equipment.A range of enclosure sizes is available allowing a broad range of battery sizes to be fitted.

GBP 297.34
1

Kentec K1619911 Battery Box to Match Syncro Styling Max 24 AH Battery Surface

Kentec K1619911 Battery Box to Match Syncro Styling Max 24 AH Battery Surface

Kentec K1619911 Battery Box to Match Syncro Styling Max 24 AH Battery SurfaceK16000 series battery enclosures provide a convenient means of fitting extra batteries for increased standby capacity for fire protection and detection systems.Ranges are available to match Syncro styled or Sigma styled control equipment. All units are constructed with the same high-quality steel and with the same finish as the control equipment.A range of enclosure sizes is available allowing a broad range of battery sizes to be fitted.

GBP 223.86
1

Kentec Sigma XT 3 Zone Single Area Extinguishant Control Panel to BS EN12094-1 K11031M2

Kentec Sigma XT 3 Zone Single Area Extinguishant Control Panel to BS EN12094-1 K11031M2

Kentec SigmaK11031M2XT 3 Zone Single Area Extinguishant Control Panel to BS EN12094-1Designed and manufactured to the highest standards in a quality controlled environment and with European EN12094-1 approvals the Sigma XT K11031M2 extinguishant releasing panel offers outstanding value and performance for all small to medium fixed fire-fighting installations. With three detection zones as standard extinguishant release can be configured to activate from any combination of detection zone inputs to allow among other combinations any two from three type activations such as would be required for detection in ceiling void room and floor void applications.The extensive configuration options of the Sigma XT K11031M2 allow the functionality of the system to be extensively modified while still complying with the requirements of the controlling standard for the equipment EN12094-1 EN54-2 and EN54-4. The panel contains a large LED display to enable easy configuration and control which also displays the time remaining until extinguishant release for added user safety. The countdown timer is duplicated on up to seven remote status units to provide local indication of the extinguishant system status. With all of the electronics mounted on a single easily removable steel plate Sigma XT panels are both robust and easy to install. Sigma XT is supplied in an enclosure that matches the design and colour of the Sigma CP range.Key FeaturesApproved to EN12094-1 EN54-2 and EN54-4Three detection zones as standardAny single zone or any combinations of zones can be configured to releaseConfigurable first stage sounder delaysConfigurable detection delaysZero time delay upon manual release optionCompatible with I.S. barriersNon-latching zone input option to receive signals from other systems such as aspirating equipmentConfigurable extinguishant delays up to 60 seconds in 5 second stepsConfigurable extinguishant duration up to 5 minutes in 5 second stepsCountdown timer shows time remaining until releaseSupports up to seven four wire status indicatorsBuilt in Extract Fan control

GBP 587.21
1

Kentec Sigma XT Extinguishant Control Panel to BS EN12094-1 2 - 8 Zone

Kentec Sigma XT Extinguishant Control Panel to BS EN12094-1 2 - 8 Zone

Kentec Sigma XT Extinguishant Control Panel to BS EN12094-1 2 - 8 ZoneSigma XT control panels are multi-area extinguishant control panels complying with EN12094-1 EN54-2 and EN54-4. Up to 8 zones of conventional detection with up to 4 extinguishant areas are available. Stand-alone extinguishant control units are also available with 2 monitored inputs to receive initiating signals from remote fire detection control panels or addressable modules. Each extinguishant area has a comprehensive set of inputs and outputs and is configurable via a simple programming interface.All extinguishant areas may have up to 7 serially connected Sigma Si status indication and control units or ancillary relay boards connected via a simple 4 core cable. The versatility of the control panel can be enhanced further by the fitting of up to 7 Sigma CP Ancillary boards K580 or Sigma CP Sounder boards K461 to the RS485 serial bus. See data sheet DS39 and DS48. For compatible status units see Sigma Si data sheet DS41.Key FeaturesApproved to EN12094-1 EN54-2 and EN54-42 4 or 8 detection zones1 to 4 extinguishant areasDual extinguishant outputs for each area configurable as MainReserveFirst and second stage sounder outputs for each areaFirst and second stage volt free changeover contacts for each areaReleased volt free contact per areaFault volt free contact per areaProgrammable extinguishant delaysProgrammable output durationExtract fan controlCountdown indicator shows time until release in secondsMode select and manual release controls per areaMonitored remote manual release inputMonitored remote Hold inputMonitored remote Mode select door interlock inputMonitored remote Released pressure switch inputMonitored remote Low Pressure switch inputMonitored Abort inputSerial connection for Sigma Si status units and ancillary boards. K588Part NumberDescriptionK21021M3Sigma XT 2 Zone Extinguishant Control Panel 1 Area SurfaceK21041M3Sigma XT 4 Zone Extinguishant Control Panel 1 Area SurfaceK21042M3Sigma XT 4 Zone Extinguishant Control Panel 2 Area SurfaceK21081M3Sigma XT 8 Zone Extinguishant Control Panel 1 Area SurfaceK21082M3Sigma XT 8 Zone Extinguishant Control Panel 2 Area SurfaceK21083M4Sigma XT 8 Zone Extinguishant Control Panel 3 Area Surface larger PSU 5.25AK21084M4Sigma XT 8 Zone Extinguishant Control Panel 4 Area Surface larger PSU 5.25A

GBP 734.00
1

Kentec RIM100M-3-K InputOutput Module For RIM100-E Ethernet LinkTwo Inputs To Monitor

Kentec RIM100M-3-K InputOutput Module For RIM100-E Ethernet LinkTwo Inputs To Monitor

Kentec RIM100M-3-K InputOutput Module For RIM100-E Ethernet LinkTwo Inputs To MonitorThe RIM100M-3-K provides a bi-directional InputOutput interface for relaying system states to RIM100E-K Ethernet modules. The RIM100M-3-K links to the RIM100E-K modules via an RS485 interface. The RIM100M-3-K supports two signal inputs and three relay outputs.The two inputs can typically be used to transfer the status of Fire and Fault states from a fire panel across a monitored link between twoRIM100E-K modules. All relay outputs are driven by signal states presented by the RIM100E-K module.The RIM100M-3-K activates an external relay contact based on the state of the monitored communication link between local and remote paired RIM100E-K modules.The module is housed in a DIN rail mountable enclosure with LED status indication visible on the front fascia of the module.Key FeaturesTwo bi-directional InputOutput signal states communicated across a link with RIM100E-K modulesSupports a simple monitored communication channel with configurable latencyAn effective solution for introducing a remote conventional Fire Alarm Control Panel to an existing network via a monitored communication channelSupport for debug via laptop with simple USB interfaceProduct is DIN rail mountableSimple LED system status indication for fire fault and monitored link

GBP 1022.52
1

Kentec K16100D3 Battery Box to Match Sigma CPXT amp Syncro AS Styling Max 38 AH Battery Surface

Kentec K16100D3 Battery Box to Match Sigma CPXT amp Syncro AS Styling Max 38 AH Battery Surface

Kentec K16100D3 Battery Box to Match Sigma CPXT Syncro AS Styling Max 38 AH Battery SurfaceK16000 series battery enclosures provide a convenient means of fitting extra batteries for increased standby capacity for fire protection and detection systems.Ranges are available to match Syncro styled or Sigma styled control equipment.All units are constructed with the same high-quality steel and with the same finish as the control equipment.A range of enclosure sizes is available allowing a broad range of battery sizes to be fitted.Key FeaturesFully welded all steel constructionTough epoxy powder coated finishKey lockableWide range of styles and sizesUp to 65Ah batteries can be fittedFully enclosed and robust construction

GBP 209.88
1

Kentec K16100M3 Battery Box to Match Sigma CPXT amp Syncro AS Styling Max 17 AH Battery Surface

Kentec K16100M3 Battery Box to Match Sigma CPXT amp Syncro AS Styling Max 17 AH Battery Surface

Kentec K16100M3 Battery Box to Match Sigma CPXT Syncro AS Styling Max 17 AH Battery SurfaceK16000 series battery enclosures provide a convenient means of fitting extra batteries for increased standby capacity for fire protection and detection systems.Ranges are available to match Syncro styled or Sigma styled control equipment. All units are constructed with the same high-quality steel and with the same finish as the control equipment.A range of enclosure sizes is available allowing a broad range of battery sizes to be fitted.

GBP 174.36
1

Kentec K16100M2 Battery Box to Match Sigma CPXT amp Syncro AS Styling Max 7 AH Battery Surface

Kentec K16100M2 Battery Box to Match Sigma CPXT amp Syncro AS Styling Max 7 AH Battery Surface

Kentec K16100M2 Battery Box to Match Sigma CPXT Syncro AS Styling Max 7 AH Battery SurfaceK16000 series battery enclosures provide a convenient means of fitting extra batteries for increased standby capacity for fire protection and detection systems.Ranges are available to match Syncro styled or Sigma styled control equipment. All units are constructed with the same high-quality steel and with the same finish as the control equipment.A range of enclosure sizes is available allowing a broad range of battery sizes to be fitted.

GBP 108.38
1

Kentec K2580003 Power Supply Boxed To Match Syncro Styling 10.25 Amp PSU Max 17 AH Battery Surface

Kentec K2580003 Power Supply Boxed To Match Syncro Styling 10.25 Amp PSU Max 17 AH Battery Surface

Kentec K2580003 Power Supply Boxed To Match Syncro Styling 10.25 Amp PSU Max 17 AH Battery SurfaceThe K408 is an EN54-4 approved universal input switching power supply capable of delivering a full 290W of continuous power for fire alarm systems. Suitable for charging a range of sealed lead acid batteries from 7Ah to 45Ah the K408 power supply features complete monitoring of primary and secondary power sources with fully temperature compensated battery charging and battery high impedance monitoring. The K408 power supplies are available as chassis only units or mounted in a range of enclosures suitable for various sizes of battery.

GBP 679.99
1

Kentec K25800M3 Power Supply Boxed To match Sigma CPXT Styling 10.25 Amp PSU Max 17 AH Battery Surface

Kentec K25800M3 Power Supply Boxed To match Sigma CPXT Styling 10.25 Amp PSU Max 17 AH Battery Surface

Kentec K25800M3 Power Supply Boxed To match Sigma CPXT Styling 10.25 Amp PSU Max 17 AH Battery SurfaceThe K408 is an EN54-4 approved universal input switching power supply capable of delivering a full 290W of continuous power for fire alarm systems. Suitable for charging a range of sealed lead acid batteries from 7Ah to 45Ah the K408 power supply features complete monitoring of primary and secondary power sources with fully temperature compensated battery charging and battery high impedance monitoring. The K408 power supplies are available as chassis only units or mounted in a range of enclosures suitable for various sizes of battery.

GBP 802.04
1

Kentec K1170-00 eNET Communications Interface Card

Kentec K1170-00 eNET Communications Interface Card

Kentec K1170-00 eNET Communications Interface CardThe flexibility of the Elite system can be further enhanced by connecting control panels and repeaters together using a high integrity network.A simple 2-wire connect between each panel allows events to be transmitted to other parts of the system to provide indication or control on a system wide basis.Using Loop Explorer configuration software up to 64 nodes can be programmed to respond in a variety of ways to any system events as required. This flexibility extends the comprehensive cause and effect programming capability of the Elite RS control panels to the entire network allowing actions test modes or disablements to be started from any point.The fault tolerance of the network is such that any single open or short circuit fault will not result in any loss of information. Multiple faults are isolated and the network breaks into smaller networks which continue to work autonomously.Key FeaturesUp to 64 nodesHigh integrity protocol when wired Class AFully secure against short or open circuit faultsSimple 2-wire loop connectionSupports open ended networks for retrofit applications

GBP 369.94
1

Kentec K1171-00 16 Channel RS485 Serial IO Interface Card

Kentec K1171-00 16 Channel RS485 Serial IO Interface Card

Kentec K1171-00 16 Channel RS485 Serial IO Interface CardTo add more IO capability to the extensive options already offered by the Elite RS control panel up to thirty two sixteen channel IO boards may be connected.When using a simple two-wire RS485 communications protocol these boards may be mounted locally to the control panel or distributed on a bus up to 1200 meters long by using a suitable cable.The flexibility of these boards is further enhanced by the fact that each of the channels is configurable as either an input or an output.Each channel may also be configured to produce a variety of input actions or respond to a variety of output types.All channels can contribute to or respond to system-wide cause and effects logic.Typical uses for IO boards include geographical LED mimic displates and plant alarm inputs.Standard Elite RS control panels contain fixings for one IO board which can easily be connected using four small signal wires to the power and comms buss within the panel. Consideration must be taken as to the loading on the main panel.

GBP 322.97
1

Kentec Syncro Ident Programmable LED Indication Panel 24 Way

Kentec Syncro Ident Programmable LED Indication Panel 24 Way

Kentec Syncro Ident Programmable LED Indication PanelSyncro Ident panels provide a compact and attractive display for up to 24 indications from a Syncro or Syncro AS fire control panel. As with all inputs and outputs on the Syncro system each indicator is fully programmable to indicate a variety of events as well as being fully programmable via cause and effects to operate in response to logically connected inputs. Each indication defaults to a zonal fire indicator but may be configured via the Loop Explorer configuration utility to operate upon any event type or combination of inputs.Requiring only a low current 24V power supply and a 2 core data connection to the fire panel Syncro Ident panels can be installed quickly and easily to provide supplementary information on the status of the fire alarm system with the minimum of cost and effort. The compact slimline enclosure is unobtrusive and is ideal for mounting in locations where a larger control and indication unit would be unsuitable. Each indication has a dedicated field for customized text to provide a concise description of the indication. Multiple Syncro Ident panels can be connected to the Syncro serial bus to provide a diverse range of indications at multiple locations.Key Features8 and 24 LED versions available as standardLarge versions available to special orderUp to 16 x 24 ways Syncro Ident can be connected to each fire panelProgrammable flashing or steady statesRed yellow or green indications optionsCommon Fire Fault and Disabled indicationCustomisable label identification tagsBuzzer with silence control and re-soundLamp test controlLow power 24V DC supplyConnects to 2 wire Syncro RS485 data busMultiple language options

GBP 384.62
1

Kentec K85001BLU BMS License Upgrade

Kentec K85001BLU BMS License Upgrade

Kentec K85001BLU BMS License UpgradeK85001BLU is a licence upgrade for the Vizulinx gateway and needs a working gateway unit to be applied. It is a software licence unlock function to activate additional Modbus BMS points within the gateway. A maximum of 9 x K85001BLU can be applied to any gateway unit.The Modbus BMS points are enumerators and therefore can be used to show all currently active events for the detection device they are mapped to. Each Modbus point can display up to 10 status flags Normal Fire Evacuate Pre-Alarm Fault Disablement test security alarm and technical alarm status for the associated device.If there is a requirement for more than 10000 Modbus BMS points then additional Vizulinx units will need to be installed on remote networked Syncro panels. It is not possible to serially connect more than one Vizulinx unit to a Syncro panel using serial data.Key FeaturesUp to 9 licence modules can be unlocked per unit10000 point maximum capacity per Vizulinx unitPoints are mapped in blocks of 250 points for each loopNon sequential loop allocation is supported i.e. Panel 1 loop 1 2 3 plus Panel 2 loop 1 1000 points

GBP 342.25
1

Kentec Main Reserve Duty Extinguishant Key Switch Unit K13480M10

Kentec Main Reserve Duty Extinguishant Key Switch Unit K13480M10

Kentec K13480M10 Main Reserve Duty Extinguishant Key Switch UnitThe K13480M10 Main Reserve switch provides a convenient and secure means to operate a switch to reserve extinguishing system agent where such provision is made as a back up to the main agent. The 901 key is common to many fire detection and protection control panels and is removable in either position. The robust enclosure allows for either surface mounting or mounting to a single gang flush box.Key FeaturesCommon 901 keyswitchKey unretainedCompatible with Sigma XT and Sigma XT modelsRobust steel enclosureSurface or single gang flush mounted

GBP 99.16
1

Kentec K1823-40 Elite Extinguishant Abort Switch Unit Grey Surface

Kentec K1823-40 Elite Extinguishant Abort Switch Unit Grey Surface

Kentec K1823-40 Elite Extinguishant Abort Switch Unit Grey SurfaceThe Sigma A-XT Abort Switch connects to the Abort terminals of the Sigma A-XT releasing panel. Any number of Sigma A-Si Abort Switches may be connected to the circuit.The last switch must have the end-of-line device from the Abort circuit terminals of the Sigma A-XT releasing panel fitted across its connections to provide open and short circuit supervision.The unit is supplied mounted to a steel enclosure but may also be flush mounted to a single gang electrical box.

GBP 79.85
1

Kentec K1823-10 Elite Extinguishant Abort Switch Unit Red Surface

Kentec K1823-10 Elite Extinguishant Abort Switch Unit Red Surface

Kentec K1823-10 Elite Extinguishant Abort Switch Unit Red SurfaceThe Sigma A-XT Abort Switch connects to the Abort terminals of the Sigma A-XT releasing panel. Any number of Sigma A-Si Abort Switches may be connected to the circuit.The last switch must have the end-of-line device from the Abort circuit terminals of the Sigma A-XT releasing panel fitted across its connections to provide open and short circuit supervision.The unit is supplied mounted to a steel enclosure but may also be flush mounted to a single gang electrical box.

GBP 79.85
1

Kentec K1822-00 Sigma A-XT Ancillary PCB

Kentec K1822-00 Sigma A-XT Ancillary PCB

Kentec K1822-00 Sigma A-XT Ancillary PCBThe Sigma A-XT Ancillary Board is compatible with all Sigma A-XT control panels. The board provides volt-free normally open contacts enabling control of sub systems and plant remotely from the main panel over a two-wire data bus.Ancillary boards require only a two-core data cable from the main control panel and a two-core power cable from the main panel.Up to seven ancillary boards can be connected to a control panel and each is allocated to an address from one to seven using a binary coded DIL switch.The total length of the data cable from the main panel to the last repeater must not exceed 4000 feet.A mixture of status units and Ancillary boards up to a maximum of seven of each type can be connected to the serial data bus.Key FeaturesTwo-wire serial connectionUp to seven per systemVolt-free relay outputs for fire and releasing system statusRelay operated LED indicatorsUL864 and FM listed

GBP 166.76
1

Kentec Syncro Net Fault Tolerant Network Interface Card - K555

Kentec Syncro Net Fault Tolerant Network Interface Card - K555

Kentec Syncro Net Fault Tolerant Network Interface Card - K555The flexibility of the Syncro system can be further enhanced by connecting control panels and repeaters together using a high integrity network. A simple 2-wire connection between each panel allows events to be transmitted to other parts of the system to provide indication or control on a system wide basis. Using the Loop Explorer configuration programme up to 64 nodes can be programmed to respond in a variety of ways to any system events as required.Features Up to 64 nodesHigh integrity protocolFully secure against short or open circuit faultsSimple 2-wire loop connectionSupports open ended networks for retrofit applicationsRepeaters share network connectionNetwork wide test and disablement functionsNetwork wide cause and effect logicFlexible configuration optionsPanels configurable to act on network events or not as requiredApollo Hochiki panels supported on single networkSyncro system can be further enhanced by connecting control panels and repeaters together using a high integrity networkFlexible configuration options

GBP 322.97
1

Kentec Syncro 16 Channel Input Output Board K560

Kentec Syncro 16 Channel Input Output Board K560

Kentec Syncro 16 Channel Input Output Board K560To add more IO capability to the extensive options already offered by the Syncro control panel up to thirty two sixteen channel IO boards may be connected. The 16 channel boards may be mixed on the RS485 bus with 8 way sounder boards 6 way sounder boards or 4 way conventional detection zone boards to provide a very flexible system of IO to satisfy any requirement.When using a simple two wire RS485 communications protocol these boards may be mounted locally to the control panel or distributed on a bus up to 1200 metres long by using a suitable cable. The flexibility of these boards is further enhanced by the fact that each of the channels is configurable as either an input or and output. Each channel may also be configured to produce a variety of input actions or respond to a variety of output types.All channels can contribute to or respond to system wide cause and effects logic. Typical uses for IO boards include geographical LED mimic displays and plant alarm inputs. Standard Syncro control panels contain fixings for one sounder relay conventional detection or IO board which can easily be connected using four small signal wires to the power and comms bus within the panel. Consideration must be taken as to the loading on the main panel.Key Features16 channelsEach channel configurable as input or outputInputs opto-isolatedOutputs open collector transistorSimple 2 wire connection to control panelUp to 32 boards supported per panel 512 InputOutput ChannelsInputs and outputs configurable as per field devicesFull cause and effects on all inputs and outputsMulti drop RS485 communicationsCan be used with other Syncro IO modules on the same panelCompatible with Syncro AS panels

GBP 287.72
1

Kentec K1810-12 Sigma A-XT Extinguishant Control Panel 115V Red

Kentec K1810-12 Sigma A-XT Extinguishant Control Panel 115V Red

Kentec K1810-12 Sigma A-XT Extinguishant Control Panel 115V RedSigma A-XT releasing panel offers outstanding value and performance for all small to medium fixed fire-fighting installations.With three initiating circuits as standard release can be configured to activate from any combination of detection zone inputs to allow among other combinations any two from three types of activations for detection in ceiling void room and floor void applications.The extensive configuration options of the Sigma A-XT allow the functionality of the system to be extensively modified. The panel contains a large LED display to enable easy configuration and control which also displays the time remaining until release for added user safety.The countdown time is duplicated on up to seven remote status units to provide local indication of the system status.With all the electronics mounted on a single easily removable steel plate Sigma A-XT panels are both robust and easy to install. Sigma A-XT is supplied in an enclosure that matches the design and colour of the Elite RS range and is available in standard red or optional grey.The K16400M2 from the extensive range of Kentec products is a syncro IO expansion card enclosure with 5.25A power supply. flexibility to create customised IO panel.Key FeaturesUL864 and FM ListedThree initiation circuits as standardAny single zone or any combinations of zones can be configured to releaseConfigurable first stage NAC delaysConfigurable detection delaysZero time delay upon manual release optionSupports up to seven four wire status indicatorsBuilt in Extract Fan controlCompatible with I.S. barriersNon-latching zone input option to receive signals from other systems such as aspirating equipmentConfigurable releasing delays up to 60 seconds in 5 second stopsConfigurable releasing duration up to 5 minutes in 5 second stepsCountdown timer shows time remaining until release

GBP 628.31
1