zone bordflag from GBP 4 | See the cheapest prices and offers on css.nordicadpartner.dk

Patol Analogue LDM-519-LP LHD Interface amp Fire Zone Monitor

Patol Analogue LDM-519-LP LHD Interface Fire Zone MonitorThe module is designed to monitor a zonal length of Analogue cable for both an elevated temperature Fire condition and Fault Status Open Short Circuit. It operates in conjunction with a single core coaxial cable and an end of line EOL terminator. The module provides early warning of hot spots and fire conditions on short sections of the overall zone length. Maximum Zone length for LHD Analogue cable is 500m when connected to this module.It is designed so that it can be configured to operate in two wire mode that emulates the operation of conventional heat detectors allowing for direct interfacing with the Fire Control panels trigger circuits.Signalling of Fire and Fault Status by means of Volt Free Contacts may also occur when a separate power supply is used. The modular form of the unit enables it to be provided in a variety of discrete housings and readily integrated into special control panels.Key FeaturesAdjustable Alarm set pointLED Indication of Fire Fault and Supply StatusAnalogue address interface Line powered configurableFault Monitoring for open short circuitsSelectable Latching Auto reset operationVFC outputs for Fire Fault conditionsOperable from two wire fire panel trigger circuits

GBP 712.32

1

Patol Analogue LDM-519-ACT-N Fire Zone Monitor with Actuation Output

Patol Analogue LDM-519-ACT-N Fire Zone Monitor with Actuation OutputThe ACT-N controller is designed to monitor a zonal length of Analogue Linear Heat Detection Cable LHDC for elevated temperature states. Two adjustable levels of alarm are provided A1 A2 one of which may be optionally employed as a Pre-Alarm. The LHDC is also monitored for fault conditions open short circuit. The Controller is provided with an output for the initiation of extinguishing media. This Actuation Output is primarily intended for the use with electrically operated chemical protractors Metrons.The ACT-N has fault monitoring circuitry appropriate to the series firing of these devices using an All Fire actuation loop configuration. LHDC is of coaxial construction and is used in conjunction with an end of line EOL terminator. The Controller provides early warning of hot spots and fire conditions on short sections of the overall LHDC zone length. Maximum LHDC zone length for Analogue cable is 500M. The modular form of the unit enables it to be provided in a variety of bespoke housings and readily integrated into special control panels.Key FeaturesTwo level alarm set pointsAdjustable alarm set point actuation loop monitoringExtinguishant actuation outputLED indication of Fire Fault and Supply statusSeparate LHDC Monitoring Actuation supplies electrically isolatedWide dc supply operation positive earthedMonitoring -20Vdc to -60VdcActuation -20Vdc to 130VdcFault monitoring for open and short circuitsSelectable latchingauto reset operationVFC relay outputs for fire and fault conditions

GBP 1056.72

1

Patol Analogue LDM-519-SEN-N LHD Fire Zone Monitor with Two Level Set Alarm Points

Patol Analogue LDM-519-SEN-N LHD Fire Zone Monitor with Two Level Set Alarm PointsThe SEN-N Controller is designed to monitor a zonal length of resettable Analogue Linear Heat detection Cable LHDC for both an elevated temperature Fire condition and Fault Status Open Short Circuit. The Controller offers two adjustable levels of alarm A1 A2 one of which may be optionally employed as a Pre Alarm. The LHDC is also monitored for fault conditions open and short circuit.LHDC is of coaxial construction and is used in conjunction with an End of Line EOL terminator. The Controller provides early warning of hot spots and fire conditions on short sections of the overall LHDC zone length. Maximum LHDC zone length for Analogue cable is 500M. The modular form of the unit enables it to be provided in a variety of bespoke housings and readily integrated into special control panels.Key FeaturesTwo level alarm set pointsAdjustable alarm set pointLED indication of Fire Fire and Supply statusWire dc supply operation -20vdc to -60vdc positive earthedFault monitoring for open short circuitsSelectable Latching Auto reset operationVFC relay outputs fore Fire Fault conditions

GBP 828.24

1

Patol N45XXA-P01 Integrated Modbus TCPIP Interface

Patol N45XXA-P01 Integrated Modbus TCPIP InterfaceModbus Slave Interface Full Temperature Trace Trace Index Timestamp Alarm Status Zone Temperature Values Max Min Avg.

GBP 1265.04

1

Patol 700-811 Digital LDM-519-DDL 2km Output Module - Legrand Enclosure

Patol 700-811 Digital LDM-519-DDL 2km Output Module - Legrand EnclosureThe LDM-519-DDL with Location Display combined with the programmable relay output module offers nine individually programmable relays used to provide location identification outputs if a Fire condition occurs along the installed LHDC.The result of the combined units is a system designed to monitor a length of Digital Linear Heat Detection Cable LHDC for both Fire condition and Fault status open circuit. It has a 3 digit LCD which activates on Fire condition and displays the distance into the zone the alarm has occurred up to 2km 1999m. The unit has an adjustment to accommodate interposing cables and has signalling of Fire and Fault status by means of volt free contacts.These contacts can then be integrated with an operator panel automation system or connection to fire zone trigger circuits or addressable interface modules.Key FeaturesDisplay of Alarm Location Distance in metresFault monitoring of LHDC for open circuit conditionsLED indication of Fire Fault and Supply status.Test Reset functionsVFC outputs for Fire Fault conditions SelectableIP65 Rated Shock Resistant PolystyreneRS 232 separate cable requiredProgrammable Relay Output Contacts

GBP 3234.58

1

Patol Digital LDM-519-DDLX LHDC Monitor and Distance Locator 10km

Patol Digital LDM-519-DDLX LHDC Monitor and Distance Locator 10kmThe module is designed to monitor a length of Digital Linear Heat Detection Cable LHDC for both fire condition and fault status open circuit.The unit is designed such that it may be configured to operate in a two-wire mode that emulates the operation of conventional heat detectors. The unit may therefore be directly interfaced with fire control panels by connection to fire zone trigger circuits or addressable interfaces.The DDL has a 3 digit LCD which activates on fire condition and displays the distance into the zone the alarm has occurred. Digital LHDC may be employed in lengths up to 10km. The unit has an adjustment to accommodate interposing cables.Signalling of fire and fault status by means of VFC may be realised when a separate supply is employed. A 4mA to 20mA instrumentation current loop output is provided for connection to PLCs etc.Key FeaturesDisplay of Alarm Location Distance in metresFault monitoring of LHDC for open circuit conditionsLED indication of Fire Fault and Supply statusTest Reset functionsOperable for two wire fire panel conventional circuits line low powerAnalogue address loop interfaceable loop powered configurable4 to 20 mA instrumentation current lop outputLHDC hazardous area use by means of intrinsically safe Zener barriersVFC outputs for fire fault conditions selectableDin Rail mounting

GBP 772.56

1

Patol Digital 90C Black Nylon Sheath Price per Meter

Patol Digital 90C Black Nylon Sheath Price per MeterThe Patol Digital Linear Heat Detection Cable is designed to provide early detection of Fire conditions and overheating in circumstances where other forms of detection would not be viable either due to an inability to sustain the environment requirements or through prohibitive costs.Extensive single zonal lengths of the LHDC Digital may be installed with the ability to trigger alarms for hot spots occurring on very small sections of the overall cable.The LHDC may be employed in a wide variety of applications but is particularly suited where there is harsh environmental condition a physical or hazardous maintenance access constraint to protect the area and or a requirement to cost effectively install detection near the risks.The primary mechanism of LHDC is that the inner core insulating polymer is specially formulated such that it plasticizes at a specific temperature.Key FeaturesSIL 2 Approved when used with DIM moduleEarly detection of hazards at temperatures well below flame pointRugged construction stainless steel outer sheath availableFixed alarm trigger temperatureCompatible with many existing zone monitors control equipmentIntrinsically safe configurable for hazardous areasUL listed

GBP 3.86

1

Patol Digital 180C Violet Hytrel Sheath Price per Meter

Patol Digital 180C Violet Hytrel Sheath Price per MeterThe Patol Digital Linear Heat Detection Cable is designed to provide early detection of Fire conditions and overheating in circumstances where other forms of detection would not be viable either due to an inability to sustain the environment requirements or through prohibitive costs.Extensive single zonal lengths of the LHDC Digital may be installed with the ability to trigger alarms for hot spots occurring on very small sections of the overall cable.The LHDC may be employed in a wide variety of applications but is particularly suited where there is harsh environmental condition a physical or hazardous maintenance access constraint to protect the area and or a requirement to cost effectively install detection near the risks.The primary mechanism of LHDC is that the inner core insulating polymer is specially formulated such that it plasticizes at a specific temperature.Key FeaturesSIL 2 Approved when used with DIM moduleEarly detection of hazards at temperatures well below flame pointRugged construction stainless steel outer sheath availableFixed alarm trigger temperatureCompatible with many existing zone monitors control equipmentIntrinsically safe configurable for hazardous areasUL listed

GBP 7.64

1

Patol Digital LDM-519-DIM Din Rail Mounted LHDC Monitor 2km

Patol Digital LDM-519-DIM Din Rail Mounted LHDC Monitor 2kmThe LDM-519-DIM module is designed to monitor a length of Digital Linear Heat Detection Cable LHDC for both a fire condition and fault status open circuit. The DIM module is certified to be fully compatible with SIL 2 certified systems.Digital LHDC may be employed in lengths up to 2Km when using the LDM-519-DIM module. Signalling of fire and fault status is generated by means of volt free contacts.The module has been specifically designed in a DIN rail format to allow it to be used in a variety of discrete housings or integrated multi zone control panels.Patol offer a complete range of special build panels which can incorporate this module for projects that require unique and tailored solutions.Key FeaturesLHDC Hazardous Area use by means of Intrinsically Safe Zener BarrierSIL 2 certifiedFault monitoring of LHDC for open circuit conditionsLED indication of Fire Fault Supply statusIntegral test reset push-buttonsVolt free contact outputs for Fire and Fault conditionsIndicator and control switch connections for local fascia implementationDin rail mounting

GBP 654.29

1

Patol Digital 180C Violet Hytrel Sheath with Stainless Steel Armour Price per Meter

Patol Digital 180C Violet Hytrel Sheath with Stainless Steel Armour Price per MeterThe Patol Digital Linear Heat Detection Cable is designed to provide early detection of Fire conditions and overheating in circumstances where other forms of detection would not be viable either due to an inability to sustain the environment requirements or through prohibitive costs.Extensive single zonal lengths of the LHDC Digital may be installed with the ability to trigger alarms for hot spots occurring on very small sections of the overall cable.The LHDC may be employed in a wide variety of applications but is particularly suited where there is harsh environmental condition a physical or hazardous maintenance access constraint to protect the area and or a requirement to cost effectively install detection near the risks.The primary mechanism of LHDC is that the inner core insulating polymer is specially formulated such that it plasticizes at a specific temperature.Key FeaturesSIL 2 Approved when used with DIM moduleEarly detection of hazards at temperatures well below flame pointRugged construction stainless steel outer sheath availableFixed alarm trigger temperatureCompatible with many existing zone monitors control equipmentIntrinsically safe configurable for hazardous areasUL listed

GBP 11.34

1

Patol Digital 90C Black Nylon Sheath with Stainless Steel Armour Price per Meter

Patol Digital 90C Black Nylon Sheath with Stainless Steel Armour Price per MeterThe Patol Digital Linear Heat Detection Cable is designed to provide early detection of Fire conditions and overheating in circumstances where other forms of detection would not be viable either due to an inability to sustain the environment requirements or through prohibitive costs.Extensive single zonal lengths of the LHDC Digital may be installed with the ability to trigger alarms for hot spots occurring on very small sections of the overall cable.The LHDC may be employed in a wide variety of applications but is particularly suited where there is harsh environmental condition a physical or hazardous maintenance access constraint to protect the area and or a requirement to cost effectively install detection near the risks.The primary mechanism of LHDC is that the inner core insulating polymer is specially formulated such that it plasticizes at a specific temperature.Key FeaturesSIL 2 Approved when used with DIM moduleEarly detection of hazards at temperatures well below flame pointRugged construction stainless steel outer sheath availableFixed alarm trigger temperatureCompatible with many existing zone monitors control equipmentIntrinsically safe configurable for hazardous areasUL listed

GBP 6.30

1

Patol Digital 70C Black Nylon Sheath Price per Meter

Patol Digital 70C Black Nylon Sheath Price per MeterThe Patol Digital Linear Heat Detection Cable is designed to provide early detection of Fire conditions and overheating in circumstances where other forms of detection would not be viable either due to an inability to sustain the environment requirements or through prohibitive costs. Extensive single zonal lengths of the LHDC Digital may be installed with the ability to trigger alarms for hot spots occurring on very small sections of the overall cable.The LHDC may be employed in a wide variety of applications but is particularly suited where there is harsh environmental condition a physical or hazardous maintenance access constraint to protect the area and or a requirement to cost effectively install detection near the risks. The primary mechanism of LHDC is that the inner core insulating polymer is specially formulated such that it plasticizes at a specific temperature.Key FeaturesSIL 2 Approved when used with DIM moduleEarly detection of hazards at temperatures well below flame pointRugged construction stainless steel outer sheath availableFixed alarm trigger temperatureCompatible with many existing zone monitors control equipmentIntrinsically safe configurable for hazardous areasUL listed

GBP 3.86

1

Patol Digital 70C Black Nylon Sheath with Stainless Steel Armour Price per Meter

Patol Digital 70C Black Nylon Sheath with Stainless Steel Armour Price per MeterThe Patol Digital Linear Heat Detection Cable is designed to provide early detection of Fire conditions and overheating in circumstances where other forms of detection would not be viable either due to an inability to sustain the environment requirements or through prohibitive costs.Extensive single zonal lengths of the LHDC Digital may be installed with the ability to trigger alarms for hot spots occurring on very small sections of the overall cable.The LHDC may be employed in a wide variety of applications but is particularly suited where there is harsh environmental condition a physical or hazardous maintenance access constraint to protect the area and or a requirement to cost effectively install detection near the risks.The primary mechanism of LHDC is that the inner core insulating polymer is specially formulated such that it plasticizes at a specific temperature.Key FeaturesSIL 2 Approved when used with DIM moduleEarly detection of hazards at temperatures well below flame pointRugged construction stainless steel outer sheath availableFixed alarm trigger temperatureCompatible with many existing zone monitors control equipmentIntrinsically safe configurable for hazardous areasUL listed

GBP 6.30

1

Patol Analogue Black Rilsan amp UV Resistant Sheath Price per Meter

Patol Analogue Black Rilsan UV Resistant Sheath Price per MeterThe Patol analogue linear heat detection cable LHDC is de-signed to provide early detection of fire and overheating in circumstances where other forms of detection would not be viable either due to inability to sustain the environment requirements or through prohibitive costs. Extensive single zonal lengths of the LHDC may be installed with the ability to trigger alarms for hot spots occurring on very small sections of the overall cable.LHDC Analogue is a coaxial cable constructed with a copper coated steel central conductor an inner insulation dielectric a tinned copper braid layer and an overall protective sheath. The primary mechanism of heat fire detection is that the resistance of the dielectric monitored between the central conductor and braid layer has a negative temperature coefficient NTC.Analogue cable is employed in conjunction with an end of line terminating device and a zone monitoring unit or control panel with an appropriate LHDC interface channel. LHDC may be installed in Hazardous areas by means of Intrinsically safe zener barriers. Similarly when the protected area is remote from the monitoring equipment interposing cables may be employed.Key FeaturesAdjustable alarm set pointRecoverable and resettable operationCan detect hot spotsZones of up to 500m in lengthMechanical chemical protection availableEasy to installCompatible with a full range of motion devicesRoHS compliant Lead Free

GBP 6.79

1

Patol Analogue Black Rilsan amp UV Resistant Sheath with Stainless Steel Armour Price per Meter

Patol Analogue Black Rilsan UV Resistant Sheath with Stainless Steel Armour Price per MeterThe Patol analogue linear heat detection cable LHDC is de-signed to provide early detection of fire and overheating in circumstances where other forms of detection would not be viable either due to inability to sustain the environment requirements or through prohibitive costs. Extensive single zonal lengths of the LHDC may be installed with the ability to trigger alarms for hot spots occurring on very small sections of the overall cable.LHDC Analogue is a coaxial cable constructed with a copper coated steel central conductor an inner insulation dielectric a tinned copper braid layer and an overall protective sheath. The primary mechanism of heat fire detection is that the resistance of the dielectric monitored between the central conductor and braid layer has a negative temperature coefficient NTC.Analogue cable is employed in conjunction with an end of line terminating device and a zone monitoring unit or control panel with an appropriate LHDC interface channel. LHDC may be installed in Hazardous areas by means of Intrinsically safe zener barriers. Similarly when the protected area is remote from the monitoring equipment interposing cables may be employed.Key FeaturesAdjustable alarm set pointRecoverable and resettable operationCan detect hot spotsZones of up to 500m in lengthMechanical chemical protection availableEasy to installCompatible with a full range of motion devicesRoHS compliant Lead Free

GBP 15.58

1

Patol Analogue Red PVC Sheath with Stainless Steel Armour Price per Meter

Patol Analogue Red PVC Sheath with Stainless Steel Armour Price per MeterThe Patol analogue linear heat detection cable LHDC is de-signed to provide early detection of fire and overheating in circumstances where other forms of detection would not be viable either due to inability to sustain the environment requirements or through prohibitive costs. Extensive single zonal lengths of the LHDC may be installed with the ability to trigger alarms for hot spots occurring on very small sections of the overall cable.LHDC Analogue is a coaxial cable constructed with a copper coated steel central conductor an inner insulation dielectric a tinned copper braid layer and an overall protective sheath. The primary mechanism of heat fire detection is that the resistance of the dielectric monitored between the central conductor and braid layer has a negative temperature coefficient NTC.Analogue cable is employed in conjunction with an end of line terminating device and a zone monitoring unit or control panel with an appropriate LHDC interface channel. LHDC may be installed in Hazardous areas by means of Intrinsically safe zener barriers. Similarly when the protected area is remote from the monitoring equipment interposing cables may be employed.Key FeaturesAdjustable alarm set pointRecoverable and resettable operationCan detect hot spotsZones of up to 500m in lengthMechanical chemical protection availableEasy to installCompatible with a full range of motion devicesRoHS compliant Lead Free

GBP 10.15

1

Patol Analogue Red PVC Sheath Price per Meter

Patol Analogue Red PVC Sheath Price per MeterThe Patol analogue linear heat detection cable LHDC is de-signed to provide early detection of fire and overheating in circumstances where other forms of detection would not be viable either due to inability to sustain the environment requirements or through prohibitive costs. Extensive single zonal lengths of the LHDC may be installed with the ability to trigger alarms for hot spots occurring on very small sections of the overall cable.LHDC Analogue is a coaxial cable constructed with a copper coated steel central conductor an inner insulation dielectric a tinned copper braid layer and an overall protective sheath. The primary mechanism of heat fire detection is that the resistance of the dielectric monitored between the central conductor and braid layer has a negative temperature coefficient NTC.Analogue cable is employed in conjunction with an end of line terminating device and a zone monitoring unit or control panel with an appropriate LHDC interface channel. LHDC may be installed in Hazardous areas by means of Intrinsically safe zener barriers. Similarly when the protected area is remote from the monitoring equipment interposing cables may be employed.Key FeaturesAdjustable alarm set pointRecoverable and resettable operationCan detect hot spotsZones of up to 500m in lengthMechanical chemical protection availableEasy to installCompatible with a full range of motion devicesRoHS compliant Lead Free

GBP 6.04

1

Vores kunder ligger øverst på Google

Google Ads Specialister fra Vestjylland

Brand

Merchant

Price (EUR)