zone bordflag from GBP 1 | See the cheapest prices and offers on css.nordicadpartner.dk

C-Tec SAF3800111 468 Zone Fire Accessory Pack

C-Tec SAF3800111 468 Zone Fire Accessory PackThe SAF3800111 manufactured by C-Tec is a 468zone fire accessory pack.

GBP 3.74

1

Hochiki TE-RH-E End Of Line Unit

Hochiki TE-RH-E End Of Line UnitAn End Of Line Unit for Hochiki CHQ Zone Modules.

GBP 0.96

1

Cooper EFXN520 Common Mounting Base

Cooper EFXN520 Common Mounting Base for Bi-Wire UltraThe FXN520 conventional standard base has been specifically designed to be compatible with the JSB range of conventional detectors. This standard base has been designed for flexibility simplicity and speed of installation. It incorporates purpose designed devices to provide fault warning if detector is removed whilst maintaining full zone wiring integrity. The base has a schotty diode in series with the negative terminals to enable fault monitoring and allow the circuit to continue if a detector is removed.Key FeaturesQuick and simple to installSeparate zone in and zone out terminalsStand-off fixing featureSelectable detector lockingBenefitsAccepts side entry surface cablesCommon base for JSB conventional detectors

GBP 4.02

1

Cooper CDBB300 Conventional Detector Mounting Base EFXN520

Cooper CDBB300 Conventional Detector Mounting Base EFXN520 Please note this will not work on the Legacy Menvier PanelsThe EFXN520 conventional standard base has been specifically designed to be compatible with the Cooper JSB range of conventional detectors. This standard base has been designed for flexibility simplicity and speed of installation.It incorporates purpose designed devices to provide fault warning if detector is removed whilst maintaining full zone wiring integrity. The base has a schotty diode in series with the negative terminals to enable fault monitoring and allow the circuit to continue if a detector is removed.Key FeaturesQuick and simple to installSeparate zone in and zone out terminalsStand-off fixing featureSelectable detector lockingBenefitsAccepts side entry surface cablesCommon base for JSB conventional detectorsInstallationBase incorporates a retaining clip to provide positive feedback when detector is correctly fitted.Separate terminals are provided for zone in and zone out connections.Each terminal can accept up to 2 x 2.5mm cablesBase incorporates a substantial cable entry aperture in the rear of the base.Breakouts are provided to enable the detector base to sit neatly over surface cables and then enter via the rear entry aperture.Base mounting incorporates a stand-off feature to help prevent distortion when mounted on anuneven surface.Fixings are suitable for standard BESA box or direct fixing to suitable surfaceOptional locking devices supplied with base to prevent unauthorised detector removal.

GBP 4.02

1

C-Tec S-KEY Spare Key for CFP Panels

C-Tec S-KEY Spare Key for CFP PanelsA spare plastic S-KEY for use C-TECs CFP XFP and ZFP fire panels.Key FeaturesProvides authorised users with access to a fire panels authorised user controlsFinished in red polycarbonate for extra strengthSuitable for use with the C-Tecs CFP 2-8 zone standard economy and AlarmSense fire panels C-Tecs XFP 1 Loop 16 Zone panel and C-Tecs full range of ZFP multi-loop addressable fire panelsDimensions 47w x 25h x 9d mmRed polycarbonate

GBP 1.93

1

Carrier B-9310 Surface Mount Back Box for Interface Modules

Carrier B-9310 Surface Mount Back Box for Interface ModulesThe B-9310 is a surface mounting backbox for use with the following range of interface modules.Compatible withC-9302 AC Control Interposing Relay ModuleC-9503E Short Circuit Loop IsolatorI-9300 Intelligent Addressable Single Input ModuleI-9301 Intelligent Addressable Single IO Interface ModuleI-9319 Intelligent Addressable Zone Monitor Module

GBP 3.35

1

Apollo Orbis TimeSaver Diode Base - ORB-DB-00003-APO

Apollo Orbis TimeSaver Diode Base - ORB-DB-00003-APOThe TimeSaver Diode Base has the same design as the standard TimeSaver Base with the addition of a diode. It is used in systems whichuse active EOL monitoring for head removal.Key Features Grouped terminals to make wiring easyTwo fixing centresLED alignment markCable stripping guideDetector locking mechanismContinuity link for voltage testing of zone wiring prior to commissioningOther devices continue to work during unauthorised removal of detectors

GBP 3.54

1

Hochiki YBN-R6BLK Conventional Mounting Base Black

Hochiki YBN-R6BLK Conventional Mounting Base BlackModel YBN-R6BLK is a Conventional Detector Mounting Base associated with the CDX Range of Detectors and is fully compatible with the majority of existing conventional fire alarm control panels. It is supplied with square cable clamps for secure and reliable cable termination but the base does not provide line continuity during detector removal therefore if Call Points are being used then these should be wired onto the zone first. The integrated third terminal provides remote indicator output.Key FeaturesIntegral remote indicator outputLow Profile only 8 mmRugged design and electronics freeQuick connections via square cable clampsAccepts 2.5 mm cablesBayonet slot low insertion force for detectorsAlso available in white or ivory

GBP 4.19

1

Hochiki Conventional White Mounting Base YBN-R6WHT

Hochiki Conventional White Mounting Base YBN-R6WHTModel YBN-R6WHT is a Conventional Detector Mounting Base associated with the CDX Range of Detectors and is fully compatible with the majority of existing conventional fire alarm control panels.It is supplied with square cable clamps for secure and reliable cable termination but the base does not provide line continuity during detector removal therefore if Call Points are being used then these should be wired onto the zone first. The integrated third terminal provides remote indicator output.Key FeaturesIntegral remote indicator outputLow Profile only 8 mmRugged design and electronics freeQuick connections via square cable clampsAccepts 2.5 mm cablesBayonet slot low insertion force for detectorsAlso available in ivory or black

GBP 2.10

1

Hochiki Conventional Standard Mounting Base YBN-R6 Ivory

Hochiki Conventional Standard Mounting Base YBN-R6 IvoryModel YBN-R6 is a Conventional Detector Mounting Base associated with the CDX Range of Detectors and is fully compatible with the majority of existing conventional fire alarm control panels.It is supplied with square cable clamps for secure and reliable cable termination but the base does not provide line continuity during detector removal therefore if Call Points are being used then these should be wired onto the zone first. The integrated third terminal provides remote indicator output.Key FeaturesIntegral remote indicator outputLow Profile only 8 mmRugged design and electronics freeQuick connections via square cable clampsAccepts 2.5 mm cablesBayonet slot low insertion force for detectorsAlso available in white or black

GBP 2.10

1

Hochiki Conventional Schottky Base YBN-R6SK Ivory

Hochiki Conventional Schottky Base YBN-R6SK IvoryModel YBN-R6SK is a Conventional Detector Mounting Base with in-line Schottky Diode associated with the CDX Range of Detectors and is fully compatible with the majority of existing conventional fire alarm control panels.It is supplied with square cable clamps for secure and reliable cable termination and the base provides line continuity during detector removal. Therefore Call Points can be wired in any order on the zone providing a suitable panel and End Of Line EOL unit is used. The integrated third terminal provides remote indicator output.Key FeaturesIntegral remote indicator outputIn-line Schottky Diode for Line ContinuityLow Profile only 8 mmRugged designQuick connections via square cable clampsAccepts 2.5 mm cablesBayonet slot low insertion force for detectors

GBP 3.11

1

Hochiki Conventional Schottky Base YBN-R6SKWHT White

Hochiki Conventional Schottky Base YBN-R6SKWHT WhiteModel YBN-R6SKWHT is a Conventional Detector Mounting Base with in-line Schottky Diode associated with the CDX Range of Detectors and is fully compatible with the majority of existing conventional fire alarm control panels.It is supplied with square cable clamps for secure and reliable cable termination and the base provides line continuity during detector removal. Therefore Call Points can be wired in any order on the zone providing a suitable panel and End Of Line EOL unit is used. The integrated third terminal provides remote indicator output.Key FeaturesIntegral remote indicator outputIn-line Schottky Diode for line continuityLow profile only 8mmRugged designQuick connections via square cable clampsAccepts 2.5mm cablesBayonet slot low insertion force for detectorsApproved by LPCB

GBP 3.11

1

Patol Digital 90C Black Nylon Sheath Price per Meter

Patol Digital 90C Black Nylon Sheath Price per MeterThe Patol Digital Linear Heat Detection Cable is designed to provide early detection of Fire conditions and overheating in circumstances where other forms of detection would not be viable either due to an inability to sustain the environment requirements or through prohibitive costs.Extensive single zonal lengths of the LHDC Digital may be installed with the ability to trigger alarms for hot spots occurring on very small sections of the overall cable.The LHDC may be employed in a wide variety of applications but is particularly suited where there is harsh environmental condition a physical or hazardous maintenance access constraint to protect the area and or a requirement to cost effectively install detection near the risks.The primary mechanism of LHDC is that the inner core insulating polymer is specially formulated such that it plasticizes at a specific temperature.Key FeaturesSIL 2 Approved when used with DIM moduleEarly detection of hazards at temperatures well below flame pointRugged construction stainless steel outer sheath availableFixed alarm trigger temperatureCompatible with many existing zone monitors control equipmentIntrinsically safe configurable for hazardous areasUL listed

GBP 3.86

1

Patol Digital 70C Black Nylon Sheath Price per Meter

Patol Digital 70C Black Nylon Sheath Price per MeterThe Patol Digital Linear Heat Detection Cable is designed to provide early detection of Fire conditions and overheating in circumstances where other forms of detection would not be viable either due to an inability to sustain the environment requirements or through prohibitive costs. Extensive single zonal lengths of the LHDC Digital may be installed with the ability to trigger alarms for hot spots occurring on very small sections of the overall cable.The LHDC may be employed in a wide variety of applications but is particularly suited where there is harsh environmental condition a physical or hazardous maintenance access constraint to protect the area and or a requirement to cost effectively install detection near the risks. The primary mechanism of LHDC is that the inner core insulating polymer is specially formulated such that it plasticizes at a specific temperature.Key FeaturesSIL 2 Approved when used with DIM moduleEarly detection of hazards at temperatures well below flame pointRugged construction stainless steel outer sheath availableFixed alarm trigger temperatureCompatible with many existing zone monitors control equipmentIntrinsically safe configurable for hazardous areasUL listed

GBP 3.86

1

NC-DB-W Conventional Detector Accessory - Base White

NC-DB-W Conventional Detector Accessory - Base WhiteThe NC-DB-W is an NC series surface mount first-fix base. Itallows any NC Series conventional point detector to be inserted removed orreplaced without rewiring using an easy twist and lock action. There are noelectrical components in the base.The NC-DB-W supports a remote indicator connection.Ease of InstallationForming an integral part of the detector assembly NC Seriesstandard bases are provided with key-hole slots for screw fixing direct toceiling structures or conduit boxes. Large rear cable entry allows for easywiring to the base.For special applications a base accessory is available forsurface installations ensuring an easy and practical installation.Ease of Wiring TestingClearly marked terminals ensure correct and secure wiringtermination for zone and remote indicator connections.Ease of UseInserting the NC Series detector into the base is accomplishedwith a simple turn and lock mechanism. To prevent unauthorised removal of adetector from its base an easy-to-activate locking mechanism is incorporatedinto all NC series detectors. If activated a detector can only be releasedfrom its base using a dedicated tool.Key FeaturesCommon first-fix mounting base for all white NC-SeriesdetectorsA selectable detector locking mechanism protects againstunauthorised removalLarge rear cable entry with ample space for cablesFlexible installation fixture with first fix screw featurereduces installation time and effortClearly visible terminal marking avoids incorrect cablingRobust wiring terminals for easy installationSimple twist-and-lock detector action ensures the detectoris properly insertedDual contact points on every connector forreliable detectorbase contact

GBP 3.43

1

Vores kunder ligger øverst på Google

Google Ads Specialister fra Vestjylland

Brand

Merchant

Price (EUR)