signal sweatshirt from GBP 182 | See the cheapest prices and offers on css.nordicadpartner.dk

C-Tec FPROSG Calibrated Audio Signal Generator

C-Tec FPROSG Calibrated Audio Signal GeneratorEnsure your induction loop systems meet current British standards with C-Tecs innovative and very cost-effective new FPROSG Audio Signal Generator. Factory calibrated to provide a fixed audio signal the generator includes all of the test tones required to test an AFILS to BS 7594 1 kHz sine wave frequency response and metal compensation plus speech and music tracks to assist with subjective testing.

GBP 252.58

1

Vox Ignis ViLX-OSA-R Lexicomm Surface Type A Fire Telephone Handset Finished in Signal Red

Vox Ignis ViLX-OSA-R Lexicomm Surface Type A Fire Telephone Handset Finished in Signal RedThese are primarily used by fire service to provide communication with the command point but may also be used by fire wardens or by stewards and marshals in sports venues. They are generally situated on or near all protected stairwells and additionally at all fire and rescue service access points.The outstation is supplied with a brushed stainless finish and can be semi recess mounted by using the optional bezel. It is operated simply by lifting the handset and is complete with a ringer and flashing red LED to indicate calling.Key featuresCompact DesignRuggedised HandsetHigh Volume RingerStatus LED20mm Cable Gland knock-outTelecoil for hearing impaired usersFull Duplex OperationFully Compliant to BS 5839-92021Magnetic Push CatchFlush bezel availableRal 3001 cw white signage. Compliant to BS5839.92021.

GBP 212.28

1

Aico Ei414 RadioLINK FireCO Alarm Interface

Aico Ei414 RadioLINK FireCO Alarm InterfaceThe Ei414 Fire CO Alarm Interface provides either a wireless interface via RF or a hard wired interface via a link cable between a RadioLINK Alarm system and a Warden Call Telecare System.The Ei414 decodes RF Fire and or CO signals from the RadioLINK and RadioLINK devices and activates the relevant onboard relays. The relays must be wired to the universal RF transmitters or via a special link cable to the Warden Call Systems. The Warden Call System in turn is programmed to perform the desired function on receipt of these signals.The Ei414 can deliver either a pulse signal or a continuous switched signal via the relays to the universal transmitters. The specific signal type will be determined by the requirement of the OEM universal sensor.The Ei414 contains x3 mains rated relays rated upto 250V AC 5 Amps. The relay contacts operate on mains power or on battery back-up cells in the event of a mains failure.The Ei414 has a key switch with 3 positionsON - Sends a signal from an Aico Alarm but not a ControllerTEST - Sends a signal from an Aico Alarm and ControllerOFF - No signal sent from an Aico Alarm or ControllerThe Ei414 uses RadioLINK multi-repeater multi-path technology to deliver very robust and reliable RF signal coverage. While designed primarily to interface with a Warden Call or similar Telecare system the versatility of the Ei414s electrically isolated contacts means it can be used to switch many other OEM devices.Key FeaturesConnect your Smoke Heat and CO Alarms system to external devices e.g. Warden Call and other Telecare systemsPowered by either mains 240V AC or 10-30V DC external sourceRechargeable lithium cell back-upVolt free contacts outputs NO NC for Alarm Fire CO messages and fault messages3 position key switchClear Indicator LEDsContains for wireless communication with Alarms and DevicesAllows for simple testing of domestic and external systemsConnects wirelessly with all other Aico wireless interconnection productsMains powered with rechargeable lithium cell back upInterfaces with TelecareWarden Call devices Sprinkler systems and many moreUses RadioLINK wireless interconnection technology to connect with domestic alarms and accessories

GBP 252.16

1

Apollo RW1800-060APO Reach Survey Kit Lite

Apollo RW1800-060APO Reach Survey Kit LiteThe RW1800-060APO is a portable battery-powered toolkit for surveying signal strength of the REACH Wireless system ahead of installation into a building.The REACH range is designed to solve challenging installation scenarios for structures with restricted or complex access and installation conditions such as listed buildings out-buildings temporary structures where wired installation or long site downtime is not possible.Key FeaturesIncludes 1x network host device 1x field-device 1x extendable detector mounting poleField-device includes an RGB LED for signal strength indicationBi-directional wireless communicationDual channel redundancy

GBP 311.16

1

C-Tec OP-6510 PA Through Screen Speech Transfer System With Tactile Pad - English

C-Tec OP-6510 PA Through Screen Speech Transfer System With Tactile Pad - EnglishA powerful bidirectional through-counter window intercom system that helps make ticket counters reception desks and other areas with a Perspex or glazed screen more accessible.Allows social distancing to be maintained by making conversations easier for all people including those wearing masks.Key FeaturesOffers full duplex sound qualityCan be easily paired to a PDA103C or ML1 hearing loop amplifier allowing the audio signal to be broadcast directly to a compatible hearing aidThree different scene settings noisystandardquietAnalog output allows conversations to be optionally recorded additional equipment requiredDSP Digital Signal Processing

GBP 369.59

1

Aritech DD669AM 20m Ceiling Mount Dual Technology Detector With Active IR Anti-Mask 18 Curtains. NC Relay Grade 3

Aritech DD669AM 20m Ceiling Mount Dual Technology Detector With Active IR Anti-Mask 18 Curtains. NC Relay Grade 3The DD600 series complement the successful EV600 series PIRs with dual technology motion sensors. The 18 curtains offer a maximum detection capability including full under crawl detection throughout a protected area of up to 20m in diameter.The unique mirror optics technology is a gliding focus which creates continuous curtains that never loses track of the intruder.4D signal processing4D signal processing makes an effective discrimination between intruder and false alarm signals. Recognizing the diversity in security applications the DD600 series features both 4D signal processing and Bi-curtain processing for the harsher environments. The combination of mirror optics with 4D signal processing not only provides better detection but also increased stability and rejection of false alarms.Range controlled radarThe DD600 sensors incorporate a unique radar technology that is range controlled and operates on 5.8 GHz frequency. The range control means that no nuisance alarms are generated for movements beyond the detection pattern.Key FeaturesDual motion sensorAutomatic reporting of all masking attemptsStep Gliding Focus Multi Curtain mirror opticRange controlled radar on 5.8 GHzPlug-in electronicsSealed optics4D processing for reduced nuisance alarmsSelectable coverage pattern using mirror masksAdditional bi-curtain processing for harsh environmentNo adjustment required for different mounting heightsEN50131-2-4 Grade 3 certifiedSeveral European approvals

GBP 211.94

1

Pepperl amp Fuchs KCD0-SD3-EX1.1045 Solenoid Driver

Pepperl Fuchs KCD0-SD3-EX1.1045 Solenoid DriverThis isolated barrier is used for intrinsic safety applications. It supplies power to solenoids LEDs and audible alarms located in a hazardous area. It is loop powered so the available energy at the output is received from the input signal. The output signal has a resistive characteristic. As a result the output voltage and current are dependent on the load and the input voltage. At full load 11 V at 80 mA is available for the hazardous area application.Details2-channel isolated barrier24 V DC supply loop poweredOutput 45 mA at 12 V DCTest pulse immunityHousing width 12.5mmUp to SIL 3 acc. to IECEN 61508

GBP 193.61

1

Pepperl amp Fuchs KFD0-SD2-EX1.1065 Solenoid Driver

Pepperl Fuchs KFD0-SD2-EX1.1065 Solenoid DriverThis isolated barrier is used for intrinsic safety applications. It supplies power to solenoids LEDs and audible alarms located in a hazardous area. It is loop powered so the available energy at the output is received from the input signal. The output signal has a resistive characteristic. As a result the output voltage and current are dependent on the load and the input voltage. At full load 11 V at 80 mA is available for the hazardous area application.Details 1-channel isolated barrier 24 V DC supply loop powered Current limit 80 mA at 11 V DC Up to SIL 3 acc. to IECEN 61508

GBP 243.10

1

Pepperl amp Fuchs KFD0-SD2-EX2.1545 Solenoid Driver

Pepperl Fuchs KFD0-SD2-EX2.1545 Solenoid DriverThis isolated barrier is used for intrinsic safety applications. It supplies power to solenoids LEDs and audible alarms located in a hazardous area. It is loop powered so the available energy at the output is received from the input signal. The output signal has a resistive characteristic. As a result the output voltage and current are dependent on the load and the input voltage. At full load 11 V at 80 mA is available for the hazardous area application.Details2-channel isolated barrier24 V DC supply loop poweredOutput 45 mA at 12 V DCTest pulse immunityUp to SIL 3 acc. to IECEN 61508

GBP 362.21

1

Pepperl Fuchs KCD0-SD-EX1.1245 Solenoid Driver

Pepperl Fuchs KCD0-SD-EX1.1245 Solenoid DriverThis isolated barrier is used for intrinsic safety applications.The device supplies power to solenoids LEDs and audible alarms located in a hazardous area.The device is loop powered so the available energy at the output is received from the input signal. The output signal has a resistive characteristic. As a result the output voltage and current are dependent on the load and the input voltageAt full load 12 V at 45 mA is available for the hazardous area application.Key Features1-channel isolated barrier24 V DC supply loop poweredCurrent limit 45 mA at 12 V DCHousing width 12.5 mmUp to SIL 3 acc. to IECEN 61508

GBP 250.44

1

Pepperl amp Fuchs KFD0-SD2-EX1.10100 Solenoid Driver

Pepperl Fuchs KFD0-SD2-EX1.10100 Solenoid DriverThis isolated barrier is used for intrinsic safety applications. It supplies power to solenoids LEDs and audible alarms located in a hazardous area. It is loop powered so the available energy at the output is received from the input signal. The output signal has a resistive characteristic. As a result the output voltage and current are dependent on the load and the input voltage. At full load 10 V at 100 mA is available for the hazardous area application.Details 1-channel isolated barrier 24 V DC supply loop powered Current limit 100 mA at 10 V DC Up to SIL 3 acc. to IECEN 61508

GBP 268.33

1

Pepperl amp Fuchs KFD0-SD2-EX1.1180 Solenoid Driver

Pepperl Fuchs KFD0-SD2-EX1.1180 Solenoid DriverThis isolated barrier is used for intrinsic safety applications. It supplies power to solenoids LEDs and audible alarms located in a hazardous area. It is loop powered so the available energy at the output is received from the input signal. The output signal has a resistive characteristic. As a result the output voltage and current are dependent on the load and the input voltage. At full load 11 V at 80 mA is available for the hazardous area application.Details 1-channel isolated barrier 24 V DC supply loop powered Current limit 80 mA at 11 V DC Up to SIL 3 acc. to IECEN 61508

GBP 260.06

1

Electro Detectors Survey Kit EDA-Z5000

Electro Detectors Survey Kit EDA-Z5000The survey kit is designed to enable the user to conduct a thorough survey for radio wireless fire alarm system signal. The frequency used is 868MHz.Kit Consists of1 x Survey Detector SSD1 x Survey Transmitter SST1 x Antenna1 x Extension Poles x4

GBP 270.00

1

Vimpex PF-KCD0-SD3-EX1.1045 Solenoid Driver - Galvanic Isolator - Single Channel

Vimpex PF-KCD0-SD3-EX1.1045 Solenoid Driver - Galvanic Isolator - Single ChannelThis isolated barrier is used for intrinsic safety applications. It supplies power to solenoids LEDs and audible alarms located in a hazardous area. It is loop powered so the available energy at the output is received from the input signal. The output signal has a resistive characteristic. As a result the output voltage and current are dependent on the load and the input voltage. At full load 11 V at 80 mA is available for the hazardous area application.Key Features2-channel isolated barrier24 V DC supply loop poweredOutput 45 mA at 12 V DCTest pulse immunityHousing width 12.5mmUp to SIL 3 acc. to IECEN 61508

GBP 386.74

1

Pepperl Fuchs KCD0-SD3-EX1.1245 Solenoid Driver

Pepperl Fuchs KCD0-SD3-EX1.1245 Solenoid DriverThis isolated barrier is used for intrinsic safety applications.The device supplies power to solenoids LEDs and audible alarms located in a hazardous area.The device is loop powered so the available energy at the output is received from the input signal. The output signal has a resistive characteristic. As a result the output voltage and current are dependent on the load and the input voltageAt full load 12 V at 45 mA is available for the hazardous area application.Key Features1-channel isolated barrier24 V DC supply loop poweredCurrent limit 45 mA at 12 V DCTest pulse immunityHousing width 12.5 mmUp to SIL 3 acc. to IECEN 61508

GBP 240.50

1

Aritech VV700 Vault Safe and ATM Seismic Detector PC Programmable - No Relay Output Board

Aritech VV700 Vault Safe and ATM Seismic Detector PC Programmable - No Relay Output BoardThe VV700 is the first fully digital seismic detector using a microprocessor that gives 100 digital signal analysis. That means the VV700 is completely adaptable for all types of applications without any compromises in detection ability. As the detector is programmed on site it can be perfectly adapted to the environment and eliminate false alarms. With this new technology the detector allow room for several different signal analysis programmes in the same hardware which previously only allowed for one. This makes the VV700 to a fully universal detector suitable for all known applications like safes vaults vault doors ATMs Night Safe Deposit Boxes weapon stores etc.Superior DetectionThe seismic detector reacts to the characteristic vibration patterns of all breaking-and-entering tools such as hammers drills diamond saws hydraulic pressure tools and thermal tools like welding torch and thermal lance. It sense vibrations that occur with a 3 to 14 meter radius of where they are mounted depending on the material and design of the protected object.Key FeaturesAritech programmable seismic detector with relay board CDigital signal processingEasy programming from laptopNo relay output board

GBP 206.64

1

Electro Detectors Zerio Plus Intelligent Antenna EDA-Z6010

Electro Detectors Zerio Plus Intelligent Antenna EDA-Z6010The EDA-Z6010 Wired Intelligent Antenna is designed for use with the Zerio Plus range of control panels. This unit is designed to be hard wired from the main control panel and positioned in areas where the signal strength from the main control panel is low.

GBP 237.00

1

Zeta SCM-ZMM Conventional Zone Monitor - 6 Circuits

Zeta SCM-ZMM Conventional Zone Monitor - 6 CircuitsThe SCM-ZMM is a six zone monitor module that is designed to be DIN mounted inside of a Smart Connect Multiloop control panel. Its powered and interfaced to the panel via a RJ45 connection.The module has six conventional zones which can be typically used for conventional devices andor for special detectors that are not available in addressable form such as UV detectors aspiration and beam detectors etc.The module monitors and transmits the status normal open short or alarm of a zone with the detectors to a control panel. Each zone input can be programmed to either give an Alarm signal or a technical alarm signal when active. The SCM-ZMM is a six zone monitor module that is designed to be DIN mounted inside of a Smart Connect Multiloop control panel. Its powered and interfaced to the panel via a RJ45 connection.The module has six conventional zones which can be typically used for conventional devices andor for special detectors that are not available in addressable form such as UV detectors aspiration and beam detectors etc. The module monitors and transmits the status normal open short or alarm of a zone with the detectors to a control panel. Each zone input can be programmed to either give an Alarm signal or a technical alarm signal when active.Key FeaturesDesigned to EN54 Part 26 x Conventional ZonesEach zone is monitored for open short circuitExtensive front unit status indicationsQuick and easy to install by plugging the RJ45 cable into the module and control panel cable supplied with unitEach zone input can be configured as either Alarm or Technical Alarm

GBP 182.12

1

Nursecall Intercall STC8 HF IR RF Activation Device

Nursecall Intercall STC8 HF IR RF Activation DeviceThe STC8 Dual Technology Personal Activation Device comprises not only of infra red transmitters battery monitor circuit with confidence LED push button activator and attack level retained peg activation method but also has a radio transmitter and aerial built into the unit. The unit once activated sends an Infra red signal as described above and simultaneously sends the same codes via the radio transmitter.This dual technology provides RF back up to the infra red or additional coverage to larger external areas such as Staff Car Parks where it is impractical to use infra red.The STC8 transmits on a high infra red frequency as well as the standard infra red frequency. This means it is ideal for use on sites where high frequency switched lighting has been installed and overcomes the potential problems associated with type of lighting technology. It can also be used on older sites where the standard Guardian AIRX4 IR Receivers have been installed.The Guardian and InterCall systems are intelligent and will only acknowledge the RF Signal if the system has NOT detected an Infrared Signal from the same user.When it has received an Infrared signal it will track the activated user cancelling alerts from past locations and only showing the currentlatest location.If the user is out of Infrared range and only RF is being detected the system will show the last known location this will be the location of the nearest RF Receiver which has a 50m range.Key FeaturesInfrared TransmitterSTC8 also has a radio transmitter and aerial built into the unitConfidence LEDPush button activator - call level 1Snatch pin - call level 2 generally AttackBoth buttons are programmable and offer a number of levels of call typeTransmit to wall mounted call points with infrared receivers or dedicated receivers mounted at high levelOnce activated sends an infrared signal as described above and simultaneously sends the same codes via the radio transmitterThis dual technology provides RF back up to the infrared or additional coverage to larger external areas such as Staff Car Parks where it is impractical to use infrared

GBP 247.86

1

Aritech VV700RC Programmable ATM Seismic Detector With Form C Relay Board

Aritech VV700RC Programmable ATM Seismic Detector With Form C Relay BoardThe VV700 is the first fully digital seismic detector using a microprocessor that gives 100 digital signal analysis. That means the VV700 is completely adaptable for all types of applications without any compromises in detection ability. As the detector is programmed on site it can be perfectly adapted to the environment and eliminate false alarms. With this new technology the detector allow room for several different signal analysis programmes in the same hardware which previously only allowed for one. This makes the VV700 to a fully universal detector suitable for all known applications like safes vaults vault doors ATMs Night Safe Deposit Boxes weapon stores etc.The seismic detector reacts to the characteristic vibration patterns of all breaking-and-entering tools such as hammers drills diamond saws hydraulic pressure tools and thermal tools like welding torch and thermal lance. It sense vibrations that occur with a 3 to 14 meter radius of where they are mounted depending on the material and design of the protected object.Key FeaturesUniversal seismic detectorDigital signal processingSpecial configuration program SCM700Programmable on site equal 100 flexibilityEasy programming from laptopSpecial analysing software for on-site performance measurementsCompatible to all existing VV600 Plus accessories

GBP 238.88

1

Baldwin Boxall VIGIL2 Weatherproof End-of-line Monitor Unit BEL1IP

Baldwin Boxall VIGIL2 Weatherproof End-of-line Monitor Unit BEL1IPAll critical signal paths of a voice alarm system must be fully monitored from the fire officers microphone through the amplifiers to the end of the loudspeaker lines. Also any faults detected with the power supply internal battery charger and backup batteries must be reported and acted upon. A VIGIL2 system has various monitoring options.BEL1IP is an active unit which is installed on each loudspeaker circuit. Up to four BEL1IP units can be placed on one speaker run. All internal DIL switches must be set correctly.Key FeaturesMonitors the critical signal path of speaker lines for open short circuit and earth faults.Fault warnings are displayed on the voice alarm rack.Each BEL1IP unit uses approximately three Watts of power. This needs to be noted when designing a system.IP65 weatherproof rated.

GBP 393.72

1

Fireclass ANN880 LED Annunciation Module

Fireclass ANN880 LED Annunciation ModuleThe ANN880 LED annunication module provides 80 red LED indications that can be programmed to signal various states. The ANN880 can be driven from either the control panel or from the remote bus.The ANN880 has 80 red LEDs numbered 1 to 80. The functionality is programmed in the MX detection panel but is defaulted to zone alarm LEDs.

GBP 359.69

1

Aritech DB995IVAS 990 Series Mounting Base w SounderVAD and Isolator

Aritech DB995IVAS 990 Series Mounting Base with SounderVAD and IsolatorThe DB995IVAS is a loop-powered 990 series compatible sounderbeacon combined with a standard 900 series mounting base. It contains a built in short circuit isolator for overload protection. The DB995IVAS is used to signal a fire alarm in enclosed areas and may be used either with a detector fitted or with a cap for operation as a stand-alone alarm device.Sounder SupportThe DB995IVAS sounders support 15 tone pairs both evacuation and alert configurable at installation time. Seven volume settings allow the sounder to be set between 60 and 90 dBA tone dependant. Country specific regulatory tones are supported for Australia Germany New Zeeland Sweden The Netherlands and the UK.SynchronisationSynchronisation of audio-visual devices ensures the integrity of the signal and is supported on the DB995IVAS. Tones from different sounders do not merge into one signal that could be mistaken for a different tone. It is also possible to synchronise with the sound and visual outputs of any other sounders and beacons connected to the same fire panel loop.Self-TestThe beacon self-test is achieved by means of an LED monitoring circuit whilst the acoustic self-test means that the sounder listens to itself when it is switched on. If the LED fails during operation or no sound is detected within 5 seconds of the sounder being switched on a fault signal is transmitted to the control panel.Sounder VAD or BothUnder normal conditions the DB995IVAS turns on the sounder and VAD at the same time but it is also possible to control sounder to VAD separately from each other simply by controls from the fire CIE.Key Features15 Alarmevacuation and 15 alertwarning tonesSeven volume levelsCPR certified under EN543 EN5417 and EN5423 Open ClassIndividual addressing and controlIndependent control of sounder and VADSetup and test at point of installationUnique beacon and acoustic self-testNEN2575 and DIN0833 compliantBuilt-in isolator with status informationSynchronisation of VAD flash alert and evacuate tonesApollo equivalent 45681-393

GBP 191.38

1

Pepperl amp Fuchs KCD2-SLD-EX1.1065 Solenoid Driver

Pepperl Fuchs KCD2-SLD-EX1.1065 Solenoid DriverThis isolated barrier is used for intrinsic safety applications. It supplies power to solenoids LEDs and audible alarms located in a hazardous area. The device is controlled with a loop powered signal or a bus powered logic signal. The device is immune to the test pulses of various control systems. The device simulates a minimum load at the input. The minimum load can be activated and de-activated. The line fault transparency function can display a line fault in the field by a change in impedance at the switching input of the solenoid driver. A line fault is indicated by a red LED and output via the fault indication output or a switch contact.Key Features1-channel isolated barrier24 V DC supply bus or loop poweredOutput 65 mA at 10 V DCLine fault transparency LFTTest pulse immunityHousing width 12.5 mmUp to SIL 3 acc. to IECEN 61508

GBP 341.28

1

Notifier Honeywell 583393.11 Fibre Optic Module for FO Switch Single Mode

Notifier Honeywell 583393.11 Fibre Optic Module for FO Switch Single ModePluggable Fibre Optic module for the fibre optic switch 583394.11 in 1310 nm single mode. This provides a fibre optic cable length up to 20km.DetailsRoHS compliantCompliant with Fast Ethernet standardCompatible with SONETSDH applicationIndustry standard small form pluggable SFP packageDuplex LV connectorDifferential LVPECL inputs and outputsSingle power supply 3.3VTTL signal detect indicatorHot PluggableClass 1 laser product complies with EN 60825-1

GBP 200.36

1

Vores kunder ligger øverst på Google

Google Ads Specialister fra Vestjylland

Brand

Merchant

Price (EUR)