Vores kunder ligger øverst på Google

Google Ads Specialister fra Vestjylland

Vi er 100% dedikerede til Google Annoncering – Vi har mange års erfaring med Google Ads og den bruger vi på at opsætte, optimere & vedligeholde vores fantastiske kunders konti.

100% Specialiseret i Google Ads
Vi har mange års erfaring fra +300 konti
Ingen lange bindinger & evighedskontrakter
Jævnlig opfølgning med hver enkelt kunde
Vi tager din virksomhed seriøst
KONTAKT OS
LÆS UDTALELSER & SUCCESHISTORIER

5 results (0,13596 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Hochiki Weatherproof Heat Detector - No Base Required DFG-60BLKJ

Hochiki Weatherproof Heat Detector - No Base Required DFG-60BLKJ

Hochiki DFG-60BLKJ Weatherproof Heat Detector No Base RequiredModel DFG-60BLKJ is a 60 C Fixed Temperature Waterproof Heat Detector the detector uses a bi-metallic strip to sense temperature change therefore consuming minimal standby current and providing high reliability.The DFG-60BLKJ is particularly suited to environments which are exposed to high levels of condensation or are hosed down. The detector has a wide operating margin allowing it to respond to both slow and fast increases in temperature it can also sense temperature reliably in a horizontal or vertical position.The DFG-60BLKJ requires no mounting base as short flying leads are provided for connection to the conventional zone and remote LED. If a backbox is required then the DFG-60BLKJ can be mounted using the Hochiki MBB-1 Marine Approved back Box.Key FeaturesWaterproof design rated to IP67Low profile shapeUtilises a bi-metallic strip to sense temperature changeNo Mounting base requiredMinimal standby currentApproved by LPCB VdS

GBP 58.16
1

Apollo XP95 DIN-Rail Dual Isolator - 55000-802APO

Apollo XP95 DIN-Rail Dual Isolator - 55000-802APO

Apollo XP95 DIN-Rail Dual Isolator - 55000-802APOThe DIN-Rail Dual Isolator provides two independent isolators which sense and isolate short circuits on Discovery and XP95 loops and spurs.OperationUnder normal operating conditions a low impedance is present between the two negative terminals of each isolator channel so that power and signals are passed to the next base in line. If a short-circuit or abnormally low impedance occurs across the loop the fall in voltage is sensed and the isolator isolates the negative supply in the direction of the fault. In this condition the yellow LED of the affected channel will be illuminated.The isolated section of loop is tested using a current pulse every five seconds. When the short-circuit is removed the power will automatically be restored. The two isolator channels are not interconnected internally and operate completely independently of one another.Key FeaturesLoop-poweredPolarity sensitiveUp to 20 detectors can be installed between isolatorsAllows fully isolated spurs

GBP 55.00
1

Apollo Discovery Marine Heat Detector 58000-400MAR

Apollo Discovery Marine Heat Detector 58000-400MAR

Apollo Discovery Marine Heat Detector 58000-400MARDiscovery Marine analogue addressable fire detectors are suitable for larger vessels. The high specification range has been developed to meet the requirements of sophisticated systems. Discovery gives you total reassurance in installations where it is necessary to adapt detection to different operating environments and where protection against unwanted alarms is paramount.The Discovery Marine Heat Detector uses a single thermistor to sense the air temperature at the detector position. The thermistor is connected in a resistor network which produces a voltage output dependent on temperature. The design of the resistor network together with the processing algorithm in the microcontroller gives an approximately linear characteristic from 10C to 80C. This lineariser signal is further processed depending on the response mode selected and converted to an analogue output.Key FeaturesApproved for use in the marine environmentFive response modes for environmental adaptationDaynight switching for increased flexibilityDrift compensation for false alarm reductionUser programmability for dataXPERT card addressing for increased securityIdeal in environments that are dirty or smokyUnaffected by wind or atmospheric pressureRemote test feature

GBP 64.84
1

Apollo Marine DIN-Rail Dual Isolator 55000-770MAR

Apollo Marine DIN-Rail Dual Isolator 55000-770MAR

Apollo Marine DIN-Rail Dual Isolator 55000-770MARThe Marine DIN-Rail Dual Isolator provides in one housing two independent isolators which sense and isolate short-circuits on loops and spurs. This unit needs to be installed in a suitable enclosure Part No. 29600-239240 or equivalent and secured using the end stops.OperationThe isolators are loop-powered and are polarity sensitive. A maximum of twenty detectors may be installed between isolators. When a short-circuit condition exists on either side of the isolator the yellow LED is illuminated.Under normal operating conditions a low impedance is present between the two negative terminals of each isolator channel so that power and signals are passed to the next base in line.If a short-circuit or abnormally low impedance occurs across the loop the fall in voltage is sensed and the isolator isolates the negative supply in the direction of the fault. In this condition the yellow LED of the affected channel will be illuminated. The isolated section of loop is tested using a current pulse every five seconds. When the short-circuit is removed the power will automatically be restored.Key FeaturesLoop-poweredUp to 20 detectors can be installed between isolatorsAllows fully isolated spurs

GBP 78.92
1

Aritech DT992 990 Series Discovery Heat Detector

Aritech DT992 990 Series Discovery Heat Detector

Aritech DT992 990 Series Discovery Heat DetectorThe DT992 is an elegant slim-line addressable heat detector that provides temperature information to the CIE. It uses a single thermistor to sense the air temperature around the detector. With its 5 operating modes it supports 5 classes of temperature detectors as stipulated by EN54.Operating ModesEvery operating mode has a different behaviour each suitable for a different application. All modes have a fixed temperature trigger with optional rate-of-rise selection allowing the detector to respond to a temperature alarm before the fixed level is reached. The DT992 supports A1R 57C with rate-of-rise A2R 61C with rate-of-rise A2S 61C static CR 90C with rate-of-rise and CS 90C static modes of operation.Unique AddressingA unique patented addressing method provides simple user-friendly and accurate identification of device location. A coded card inserted in the base is read by the detector as it is plugged in. All the electronic components are in the detector but the location information is held in the base. Addressing errors during maintenance are eliminated because the address remains in the base. Pre-coded and pre-numbered address cards are available.ApplicationsThe DT992 is ideal for use in environments that are dirty or smoky under normal conditions. It is therefore well suited installation in warehouses loading bays and car parks.Key Features5 Approved response modes for ease of optimisation to different environmentsRejection of transient signalsDrift compensation to ensure constant sensitivity360 Alarm visibilityFlashing LED optionFast alarm reportingEN54 approved and CPR certifiedApollo equivalent 58000-400

GBP 51.05
1